Hi,
for comparison I have a similar PC at the same provider and
it works fine (I have fxp at irq 11 though, and use -current).
Also I had used the original floppy image to install OpenBSD:
wget ftp://ftp.de.openbsd.org/pub/snapshots/i386/floppy38.fs
dd of=/dev/hda if=floppy38.fs bs=1k count=1440
Sven, are you sure your fxp is not working? Maybe just your
network settings are wrong? Here are mine (stolen from Kili):
/etc/hostname.fxp0:
inet 81.169.186.XXX 255.255.255.255 NONE
!route add 81.169.186.1 -link \$if: -interface
/etc/mygate:
81.169.186.1
/etc/resolv.conf:
lookup file bind
nameserver 81.169.163.106
nameserver 81.169.163.104
Regards
Alex
PS: Here is my dmesg, works ok:
OpenBSD 3.8-current (GENERIC) #0: Mon Jan 16 10:28:09 CET 2006
[EMAIL PROTECTED]:/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(R) CPU 2.40GHz ("GenuineIntel" 686-class) 2.40 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,
ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID
real mem = 402169856 (392744K)
avail mem = 359624704 (351196K)
using 4278 buffers containing 20209664 bytes (19736K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(d0) BIOS, date 02/03/04, BIOS32 rev. 0 @ 0xfb330
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf84
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde90/240 (13 entries)
pcibios0: PCI Exclusive IRQs: 5 9 10 11 12
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371SB ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000 0xc9000/0x1000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845 Host" rev 0x04
ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP" rev 0x04
pci1 at ppb0 bus 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x05
pci2 at ppb1 bus 2
fxp0 at pci2 dev 6 function 0 "Intel 8255x" rev 0x08, i82559: irq 11, address 00
:30:48:53:3c:96
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci2 dev 7 function 0 "Intel 8255x" rev 0x08, i82559: irq 10, address 00
:30:48:53:3c:97
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
vga1 at pci2 dev 8 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x05
pciide0 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x05: DMA, channel 0 w
ired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IC35L060AVV207-0>
wd0: 16-sector PIO, LBA48, 58644MB, 120103200 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
pciide0: channel 1 disabled (no drives)
ichiic0 at pci0 dev 31 function 3 "Intel 82801BA SMBus" rev 0x05: irq 9
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f365 netmask ff65 ttymask ffe7
pctr: user-level cycle counter enabled
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
arpresolve: unresolved and rt_expire == 0
On 1/20/06, Sven Wolf <[EMAIL PROTECTED]> wrote:
> I've a server at the German hoster Strato and I try to install OpenBSD
> 3.8 on this machine. But I always get a device timeout of the Intel Nic
> (because of a wrong irq assignment?) :(
>
> Here is the dmesg output:
>
> OpenBSD 3.8 (RAMDISK) #9: Tue Jan 17 18:24:51 CET 2006
> [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK
> cpu0: Intel(R) Celeron(R) CPU 2.40GHz ("GenuineIntel" 686-class) 2.40 GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,
> ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID
> real mem = 536387584 (523816K)
> avail mem = 485179392 (473808K)
> using 4278 buffers containing 26923008 bytes (26292K) of memory
> mainbus0 (root)
> acpi0 at mainbus0: revision 0 attached
> acpitimer at acpi0 not configured
> acpi device at acpi0 from table DSDT not configured
> acpi device at acpi0 from table FACP not configured
> bios0 at mainbus0: AT/286+(c0) BIOS, date 05/27/03, BIOS32 rev. 0 @ 0xfb330
> apm0 at bios0: Power Management spec V1.2
> apm0: flags 70102 dobusy 1 doidle 1
> pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf84
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde90/240 (13 entries)
> pcibios0: PCI Exclusive IRQs: 5 10 11 12
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371SB ISA" rev 0x00)
> pcibios0: PCI bus #2 is the last bus
> bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1000
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82845 Host" rev 0x04
> ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP" rev 0x04
> pci1 at ppb0 bus 1
> ppb1 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x05
> pci2 at ppb1 bus 2
> fxp0 at pci2 dev 6 function 0 "Intel 82557" rev 0x08, i82559: irq 12,
> address 00 :30:48:52:c9:fc
> inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
> fxp1 at pci2 dev 7 function 0 "Intel 82557" rev 0x08, i82559: irq 12,
> address 00 :30:48:52:c9:fd
> inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
> vga1 at pci2 dev 8 function 0 "ATI Rage XL" rev 0x27
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x05: failed
> to map I /O space
> pciide0 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x05: DMA,
> channel 0 w ired to compatibility, channel 1
> wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <ExcelStor Technology J360>
> wd0: 16-sector PIO, LBA48, 58644MB, 120103200 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> pciide0: channel 1 disabled (no drives)
> "Intel 82801BA SMBus" rev 0x05 at pci0 dev 31 function 3 not configured
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom0: console
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> biomask ede5 netmask fde5 ttymask ffe7
> rd0: fixed, 3800 blocks
> dkcsum: wd0 matches BIOS drive 0x80
> root on rd0a
> rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
>
> I've created my own bootfloppy because with the default OpenBSD 3.8
> bootfloppy I get the same error. I've played (enabled/disabled) with
> following kernel options without luck:
>
> option PCIBIOS_INTR_FIXUP_FORCE
> option PCI_INTR_FIXUP (as for the netbsd kernel)
> option USER_PCICONF # user-space PCI configuration
> option BOOT_CONFIG # boot-time kernel config
> pcibios0 at bios0 flags 0x0008 (set to 0x0004, 0x0008, 0x0030)
> acpi0 at mainbus?
> #acpitimer* at acpi?
> #hpet* at acpi?
> option ACPIVERBOSE
> option ACPI_ENABLE
>
> Has anyone any idea how I can assign an another irq than 12 to fxp? In
> my opinion this is the problem :(
