Once you get to OCTEON III class with -current, software FP emulation is no longer at play. Ubiquiti Edgerouter 4, 6 and Infinity all fit this class. 4 to 16 cores. Not bad.
Martijn van Duren [openbsd+m...@list.imperialat.at] wrote: > On 09/13/17 22:28, Dante F. B. Col?? wrote: > > Hi > > > > I'm think about get a Ubiquiti Edgerouter box and drop openbsd there. > > I read the instalation file and was not clear to me if the current > > MIPS/Octeon kernel implementation supports SMP or not , does it support ? > > > > Regards > > > > Dante F. B. Col?? > > > Yes it does, just don't forget to set numcores/coremask in the boot > command. > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org > > OpenBSD 6.1 (GENERIC.MP) #0: Mon Apr 3 08:08:00 UTC 2017 > visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP > real mem = 2147483648 (2048MB) > avail mem = 2113486848 (2015MB) > warning: no entropy supplied by boot loader > mainbus0 at root > cpu0 at mainbus0: CN61xx CPU rev 0.1 800 MHz, Software FP emulation > cpu0: cache L1-I 512KB D 8KB 64 way, L2 1024KB 8 way > cpu1 at mainbus0: CN61xx CPU rev 0.1 800 MHz, Software FP emulation > cpu1: cache L1-I 512KB D 8KB 64 way, L2 1024KB 8 way > clock0 at mainbus0: int 5 > iobus0 at mainbus0 > octuctl0 at iobus0 base 0x118006f000000 irq 56 > ehci0 at octuctl0 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Octeon EHCI root hub" rev > 2.00/1.00 addr 1 > ohci0 at octuctl0, version 1.0 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 configuration 1 interface 0 "Octeon OHCI root hub" rev > 1.00/1.00 addr 1 > octrng0 at iobus0 base 0x1400000000000 irq 0 > cn30xxgmx0 at iobus0 base 0x1180008000000 > cnmac0 at cn30xxgmx0: SGMII, address 24:a4:3c:06:a2:72 > ukphy0 at cnmac0 phy 4: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac1 at cn30xxgmx0: SGMII, address 24:a4:3c:06:a2:73 > ukphy1 at cnmac1 phy 5: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac2 at cn30xxgmx0: SGMII, address 24:a4:3c:06:a2:74 > ukphy2 at cnmac2 phy 6: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac3 at cn30xxgmx0: SGMII, address 24:a4:3c:06:a2:75 > ukphy3 at cnmac3 phy 7: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cn30xxgmx1 at iobus0 base 0x1180010000000 > cnmac4 at cn30xxgmx1: SGMII, address 24:a4:3c:06:a2:76 > ukphy4 at cnmac4 phy 0: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac5 at cn30xxgmx1: SGMII, address 24:a4:3c:06:a2:77 > ukphy5 at cnmac5 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac6 at cn30xxgmx1: SGMII, address 24:a4:3c:06:a2:78 > ukphy6 at cnmac6 phy 2: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > cnmac7 at cn30xxgmx1: SGMII, address 24:a4:3c:06:a2:79 > ukphy7 at cnmac7 phy 3: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x180361, model 0x0004 > simplebus0 at iobus0: "soc" > octmmc0 at simplebus0 > sdmmc0 at octmmc0: 8-bit, mmc high-speed > uartbus0 at mainbus0 > com0 at uartbus0 base 0x1180000000800 irq 34: ns16550a, 64 byte fifo > com0: console > com1 at uartbus0 base 0x1180000000c00 irq 35: ns16550a, 64 byte fifo > /dev/ksyms: Symbol table not valid. > ural0 at uhub0 port 1 configuration 1 interface 0 "Cisco-Linksys Wireless-G > USB Network Adapter" rev 2.00/0.04 addr 2 > ural0: MAC/BBP RT2571 (rev 0x05), RF RT2526, address 00:14:bf:75:9a:45 > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <Sandisk, SEM04G, 0000> SCSI2 0/direct removable > sd0: 3776MB, 512 bytes/sector, 7733248 sectors > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > boot device: sd0 > root on sd0a (5e15570835adc5f6.a) swap on sd0b dump on sd0b
