Howdy.
I found a working USB (Sandisk Cruzer Fit 8GB) to install 6.2 on a RPI3.
Install went fine and so was first boot, then I noticed that relinking
the kernel failed.
Below is my dmesg and error log.
I thought it might have been due to the clock being way skewed by I
sync'ed it manually and still run into the same error.
Any pointers on how to proceed?
+--+
Carlos
OpenBSD 6.2 (GENERIC) #34: Tue Oct 3 23:53:05 MDT 2017
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 964972544 (920MB)
avail mem = 909017088 (866MB)
mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2
cpu0 at mainbus0: ARM Cortex-A53 r0p4
simplefb0 at mainbus0: 656x416
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
simplebus0 at mainbus0: "soc"
bcmintc0 at simplebus0
bcmdog0 at simplebus0
pluart0 at simplebus0
bcmaux0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
dwctwo0 at simplebus0
agtimer0 at simplebus0: tick rate 19200 KHz
syscon0 at simplebus0
simplebus1 at mainbus0: "clocks"
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev
2.00/1.00 addr 1
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems product
0x9514" rev 2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address b8:27:eb:1c:06:b7
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
umass0 at uhub1 port 5 configuration 1 interface 0 "SanDisk Cruzer Fit" rev
2.10/1.00 addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct
removable serial.07815571040905110075
sd0: 7632MB, 512 bytes/sector, 15630336 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (b045dd5058980495.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
# cat /usr/share/compile/GENERIC/relink.log
(SHA256) /bsd: OK
LD="ld" sh makegap.sh 0xd4d4d4d4 gapdummy.o
ld: error: gap.link:11: unknown command ;
ld: error: gap.link:11: LONG(0xd4d4d4d4);
ld: error: gap.link:11: ^
ld: error: cannot open gapdummy.o: No such file or directory
ld: error: target emulation unknown: -m or at least one .o file required
*** Error 1 in /usr/share/compile/GENERIC (Makefile:529 'newbsd')
