On Tue, Jan 16, 2018 at 3:27 PM, Scott Bennett <[email protected]>
wrote:
> On 1/15/2018 5:30 PM, jungle Boogie wrote:
>> On 12 January 2018 at 08:24, Scott Bennett <[email protected]>
wrote:
>>> After reading INSTALL.octeon, I was able to write miniroot62.fs to a
usb,
>>> plug that into the ERL, and perform a normal installation. The problem
is
>>> that the installer was not able to detect both cores, so it only
installed
>>> bsd.sp (bsd.mp was not an option in the set selection).
>>
>> See this post:
>> https://an.undulating.space/post/171020-erl-openbsd-smp/
>>
>> See this reddit thread:
>>
https://www.reddit.com/r/openbsd/comments/7agdgh/openbsd_62_on_edgerouter_lite_with_bsdmp/
>>
>> Hope that helps
>
> Much appreciated! The reddit thread may just work.
>
Greetings all, and thanks for the info on getting the MP installed on the
ERL.
I performed the steps as indicated n the links above and now have GENERIC.MP
running on my ERL. I did see that KARL failed on the initial install and
reboot,
which I performed via serial console. I attempted
the manual relinking and a
second reboot via ssh, so I don't know if it failed
on the second reboot. If it did,
I
can live without it
in order to have a second core
as intended on this device.
Thanks again, dmesg to follow.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.2 (GENERIC.MP) #0: Wed Oct 4 05:08:15 UTC 2017
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP
real mem = 536870912 (512MB)
avail mem = 523943936 (499MB)
mainbus0 at root
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
cpu1 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu1: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
cn30xxsmi0 at simplebus0
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
2.00/1.00 addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:c8
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:c9
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:ca
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive"
rev 2.10/11.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> SCSI4 0/direct
removable serial.05dca83aZB0L2W63LA4P
sd0: 30526MB, 512 bytes/sector, 62517248 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (fb74a192b03ee90f.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
