I tried to upgrade an old server with 3.8 via a floppy. It was running 3.7
with a DB and web server previously.
During the upgrade, it did not detect the NIC. As it was a test server, I
tried a re-install rather than an upgrade...same thing.
The 3.7 install disk works so I know it is not a problem with the card or the
floppy. I tried pulling the floppy38.fs several times and running a dd to put
the a couple of known good floppies all with the same results.
Below is the dmesg from the 3.7 server after the rebuild.
Any help would be appreciated.
Thanks,
Mike Calvi
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 267 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX
real mem = 670658560 (654940K)
avail mem = 604454912 (590288K)
using 4278 buffers containing 33636352 bytes (32848K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(70) BIOS, date 03/03/00, BIOS32 rev. 0 @ 0xf0530
apm0 at bios0: Power Management spec V1.2 (BIOS mgmt disabled)
apm0: APM power management enable: unrecognized device ID (9)
apm0: APM engage (device 1): power management disabled (1)
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdb2
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf0d20/144 (7 entries)
pcibios0: PCI Interrupt Router at 000:04:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x5000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage Pro" rev 0x5c
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 4 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 4 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DHEA-38451>
wd0: 16-sector PIO, LBA, 8063MB, 16514064 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1 at pciide0 channel 1 drive 0: <WDC WD600BB-32CCB0>
wd1: 16-sector PIO, LBA, 57241MB, 117231408 sectors
wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 4 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power Mgmt" rev 0x02 at pci0 dev 4 function 3 not configured
ahc1 at pci0 dev 6 function 0 "Adaptec AIC-7890/1 U2" rev 0x00: irq 11
scsibus0 at ahc1: 16 targets
cd0 at scsibus0 targ 4 lun 0: <YAMAHA, CRW4416S, 1.0g> SCSI2 5/cdrom removable
tx0 at pci0 dev 9 function 0 "SMC 83C170 (EPIC/100)" rev 0x06: irq 11 address
00:e0:29:09:3d:42
qsphy0 at tx0 phy 3: QS6612 10/100 PHY, rev. 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83781D
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ef65 netmask ef65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
