On 3/22/06, Bachman Kharazmi <[EMAIL PROTECTED]> wrote:
>
> After I downloaded the sets successfully and the rest of the
> installation went fine I tried to reboot the system, what happens
> after reboot is nothing. No "boot >", but I can enter the maintaing
> menu.
>
> Maybe of these lines have to be changed in console(maintain menu):
> SystemPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(8)
> OSLoadPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(0)
>
> In case that's my problem I don't know which one to change.
> printenv is pasted bellow.
>
> System Maintenance Menu
>
> 1) Start System
> 2) Install System Software
> 3) Run Diagnostics
> 4) Recover System
> 5) Enter Command Monitor
>
> Option? 5
> Command Monitor. Type "exit" to return to the menu.
> > printenv
> AutoLoad=Yes
> diskless=0
> dbaud=9600
> volume=80
> sgilogo=y
> monitor=h
> TimeZone=PST8PDT
> netaddr=192.0.2.1
> crt_option=1
> SystemPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(8)
> OSLoadPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(0)
> OSLoader=boot
> OSLoadFilename=/bsd.rd
> OSLoadOptions=auto
> console=d
> ConsoleOut=serial(0)
> ConsoleIn=serial(0)
> cpufreq=270
> eaddr=08:00:69:0e:9b:ab
> videostatus=illegal_env_var
> On 22/03/06, Bachman Kharazmi <[EMAIL PROTECTED]> wrote:
> > cool, it booted and I'm setting up my disk now :)
> > thanks guys for all your replies.
> > /bkw
> > On 22/03/06, Bachman Kharazmi <[EMAIL PROTECTED]> wrote:
> > > I've two SGI O2 R12000 at home from today for experimental use.
> > > They've 32 of them unused at my uni so the admin said it was ok to
> > > take two :)
> > >
> > > Now I've problems installing osbd 3.8, I've choosed the cdboot
> > > installation method.
> > > First I : 'resetenv' then setenv OSLoader=boot and setenv
> OSLoadFilename=/bsd.rd
> > > Then I choose Install program from CDrom in the maintaining menu.
> > >
> > > What I can see on the screen is all the boot arguments at top (from
> > > the environment).
> > >
> > > OpenBSD/sgi Arcbios boot
> > > Boot: pci(0)scsi(0)cdrom(4)partition(0)/bsd.rd
> > > Loading ELF64 file
> > > 0xfff....... Loading symbol table
> > > Start at 0x....
> > > ARCS32 Firmware Version 1.10
> > > SR=34010080
> > > Found SGI-IP32, setting up.
> > > And here it freeze, nothing else happens.
> > >
> > > any ideas are welcome, /bkw
Hello, here is my 02 setup and dmesg.
rogern
John 3:16
obsd39# cu -l tty00
Connected
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
>
> printenv
AutoLoad=Yes
console=g
diskless=0
dbaud=9600
volume=80
sgilogo=y
monitor=h
TimeZone=PST8PDT
netaddr=192.0.2.1
SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
OSLoadFilename=/bsd
OSLoader=boot
cpufreq=180
eaddr=08:00:69:02:df:19
NoAutoLoad=CONSOLE OPEN FAILED.
ConsoleOut=serial(0)
ConsoleIn=serial(0)
> exitCannot connect to keyboard -- check the cable.
Cannot open keyboard() for input
Cannot connect to keyboard -- check the cable.
Cannot open keyboard() for input
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 1
Starting up the system...
arg 0: pci(0)scsi(0)disk(1)rdisk(0)partition(8)/boot
arg 1: OSLoadOptions=auto
arg 2: ConsoleIn=serial(0)
arg 3: ConsoleOut=serial(0)
arg 4: SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 5: OSLoader=boot
arg 6: OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
arg 7: OSLoadFilename=/bsd
OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
Loading ELF64 file
0xffffffff80100000:0x310d50, Zero 0xffffffff80410d50:0x5bb80, Loading symbol
table
Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34010080
Found SGI-IP32, setting up.
Initial setup done, switching console.
NOTE: TLB code too large, using trampolines
[ using 267936 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.8-beta (GENERIC) #156: Fri Aug 19 08:40:40 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 134217728
rsvd mem = 7020544
avail mem = 108875776
using 1638 buffers containing 6709248 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev
1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
ahc0: target 1 using 8bit transfers
ahc0: target 1 using asynchronous transfers
sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2
5/cdrom removable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
com0 at macebus0: ns16550a, 16 byte fifo
com0: console
com1 at macebus0: ns16550a, 16 byte fifo
mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
mavb0 at macebus0: AD1843 rev 1
audio0 at mavb0
boot device: sd0.
root on sd0a
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
rootdev=0x0 rrootdev=0x900 rawdev=0x902
Automatic boot in progress: starting file system checks.
/dev/rsd0a: file system is clean; not checking
/dev/rsd0f: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
/dev/rsd0d: file system is clean; not checking
/dev/rsd0e: file system is clean; not checking
setting tty flags
starting network
starting system logger
starting rpc daemons: ntpd.
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files
starting network daemons: sendmail inetd sshd.
starting local daemons:.
standard daemons: cron.
Wed Mar 22 16:16:35 PST 2006
OpenBSD/sgi (02.Joshua.local) (tty00)
login:
--
