Following on that vmm/Alpine/Docker/Jellyfin install:
I should now be able, according to the Docker documentation,
to log into the Jellyfin server administration interface
through http://myalpinevm:8096/ (in place of localhost)
However, for this I need my vm to be accessible through
the local network as if it were any other regular device
connected to my ISP's box that acts as a router. If I
understand correctly, this is described in the last section
(Option 4 - VMs on the real network) of the FAQ.
Following that tutorial, I have tried various configurations
without success.
As of now, I have omitted vport0 in the configuration as per
the last sentence in the FAQ. Not sure if I should have been
doing something else as well.
Currently my ethernet device eth0 has been disconnected.
I can still access my server through the wireless athn0 device.
Here is what I have:
srv$ more /etc/hostname.re0
inet autoconf
inet6 autoconf
srv$ more /etc/hostname.veb0
add re0
up
srv$ ifconfig
lo0: flags=2008049<UP,LOOPBACK,RUNNING,MULTICAST,LRO> mtu 32768
index 4 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet 127.0.0.1 netmask 0xff000000
re0:
flags=a48b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST,AUTOCONF6TEMP,AUTOCONF6,AUTOCONF4>
mtu 1500
lladdr 08:60:6e:eb:54:8b
index 1 priority 0 llprio 3
media: Ethernet autoselect (1000baseT
full-duplex,rxpause,txpause)
status: active
inet6 fe80::a60:6eff:feeb:548b%re0 prefixlen 64 scopeid 0x1
athn0:
flags=a48843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF6TEMP,AUTOCONF6,AUTOCONF4>
mtu 1500
lladdr 00:26:b6:f5:be:78
index 2 priority 4 llprio 3
groups: wlan egress
media: IEEE802.11 autoselect (HT-MCS3 mode 11n)
status: active
ieee80211: join sylvainsab chan 100 bssid c0:3c:04:fc:d5:94
-71dBm wpakey wpaprotos wpa2 wpaakms psk wpaciphers ccmp wpagroupcipher
ccmp
inet6 fe80::226:b6ff:fef5:be78%athn0 prefixlen 64 scopeid 0x2
inet 10.0.0.2 netmask 0xffffff00 broadcast 10.0.0.255
inet6 2001:861:2c20:70:36ec:9a07:7fcd:50c5 prefixlen 64 autoconf
temporary pltime 14397 vltime 86397
inet6 2001:861:2c20:70:fade:a8c6:347a:3d91 prefixlen 64 autoconf
pltime 14397 vltime 86397
enc0: flags=0<>
index 3 priority 0 llprio 3
groups: enc
status: active
veb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST>
description: switch1-my_switch
index 5 llprio 3
encap: vnetid 1 txprio packet rxprio outer
groups: veb
re0 flags=3<LEARNING,DISCOVER>
port 1 ifpriority 0 ifcost 0 untagged 1
tagged: none
tap0 flags=3<LEARNING,DISCOVER>
port 7 ifpriority 0 ifcost 0 untagged 1
tagged: none
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33136
index 6 priority 0 llprio 3
groups: pflog
tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu
1500
lladdr fe:e1:ba:d0:a7:aa
description: vm1-if0-alpine
index 7 priority 0 llprio 3
groups: tap
status: active
I might try exactly following the FAQ as I did before,
i.e. not omitting vport0, but I am not very hopeful.
In any case, can you confirm that there is a way to
configure the network so that I can access my vm to
and from my other LAN machines ? Previously I was able
to ping any machine from the vm but not vice-versa.
Does it have to do with the limitations of using one's
ISP's box as router ?
Cheers
--
Sylvain Saboua
looking for a PDP-11
