Hello misc,
I have a problem with booting the MP kernel, it just hangs during boot.
The server is an old big HP NetServer LH II with two P2 300MHz
processors. It worked very good on Linux with SMP. It's running OpenBSD
since 3.7 and since then it doesn't boot with GENERIC.MP kernel. GENERIC
works very fine, no problems at all.
Today I booted into UKC, turned verbose on, but it didn't provided me
with more info. Last lines during boot are:
>>> probind for isapnp0
>>> probind for isapnp0 failed
>>> probind for pcic0
>>> probind for pcic0 failed
>>> probind for pcic1
>>> probind for pcic1 failed
>>> probind for pcic2
>>> probind for pcic2 failed
biosmask 0 netmask 0 ttymask 0
isapic0: pin 11 shares different IML interrputs (40..50), degraded
performance
^^^^^^^ ^^^
I'm not sure if these are ok, my "notes" are hard to read, damn ;-)
I will have serial cable this week so I will be able to dump full text
from booting.
After that message nothing more happens. I waited for around 4 minutes,
and then rebooted into GENERIC.
IIRC 3.7 hanged in a different way, on scsi/raid devices.. turning them
off didn't help a bit. Below is the full dmesg from GENERIC kernel,
machine works ok on it.
Please tell me if you need any other information on this. Or maybe some
workaroung exists? Some devices to turn off in UKC or sth?
azazel [22:24:56] ~ # dmesg
OpenBSD 3.9-stable (GENERIC) #0: Tue May 2 12:23:33 CEST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 301 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX
real mem = 536453120 (523880K)
avail mem = 482488320 (471180K)
using 4278 buffers containing 26927104 bytes (26296K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(0e) BIOS, date 08/12/99, BIOS32 rev. 0 @ 0xf5597
pcibios0 at bios0: rev 2.1 @ 0xf53b0/0x1120
pcibios0: PCI BIOS has 8 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 7 9 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x600
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82441FX" rev 0x02
ami0 at pci0 dev 7 function 0 "AMI MegaRAID Series 428" rev 0x03: irq 9
AMI 428 32b
ami0: FW A.03.00, BIOS vA.03.00, 4MB RAM
ami0: 3 channels, 16 targets, 1 logical drives
scsibus0 at ami0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/direct fixed
sd0: 20330MB, 20330 cyl, 64 head, 32 sec, 512 bytes/sec, 41635840 sec total
ppb0 at pci0 dev 8 function 0 "DEC 21052 PCI-PCI" rev 0x02
pci1 at ppb0 bus 1
rl0 at pci1 dev 1 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:02:44:7c:8c:f0
rlphy0 at rl0 phy 0: RTL internal PHY
xl0 at pci1 dev 2 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 7,
address 00:60:97:4b:17:14
nsphy0 at xl0 phy 24: DP83840 10/100 PHY, rev. 0
fxp0 at pci1 dev 3 function 0 "Intel 8255x" rev 0x02, i82557: irq 10,
address 00:60:b0:6c:7d:6b
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 0
"Intel 82375EB EISA" rev 0x15 at pci0 dev 9 function 0 not configured
ahc0 at pci0 dev 10 function 0 "Adaptec AIC-7880" rev 0x00: irq 11
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc0: 16 targets
cd0 at scsibus1 targ 5 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0787> SCSI2
5/cdrom removable
ahc1 at pci0 dev 11 function 0 "Adaptec AIC-7880" rev 0x00: irq 11
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus2 at ahc1: 16 targets
eisa0 at mainbus0
eisa0: can't map I/O space for slot 14
eisa0: can't map I/O space for slot 15
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
vga0 at isa0 port 0x3b0/48 iomem 0xa0000/131072
wsdisplay0 at vga0 mux 1: console (80x25, vt100 emulation), using wskbd0
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask fb65 netmask ffe5 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
--
.: Jakub G3azik
.: zytek(at)ostrow-wlkp.net
.: jid:zytek(at)azazel.ostrow-wlkp.net
