Hello,
I hope this is an appropriate list to post this question to.
the problem is that "xset dpms force off" does not do anything visible. my
laptop's screen does not switch off. does not even go blank.
the output of "xset -q" is below. dmesg, /var/log/Xorg.0.log and
/etc/X11/xorg.conf are attached.
please help!
thanks!
konstantin
Keyboard Control:
auto repeat: on key click percent: 0 LED mask: 00000000
auto repeat delay: 500 repeat rate: 30
auto repeating keys: 00ffffffdffffbbf
fadfffdfffdfe5ef
ffffffffffffffff
ffffffffffffffff
bell percent: 50 bell pitch: 400 bell duration: 100
Pointer Control:
acceleration: 2/1 threshold: 4
Screen Saver:
prefer blanking: yes allow exposures: yes
timeout: 600 cycle: 600
Colors:
default colormap: 0x20 BlackPixel: 0 WhitePixel: 65535
Font Path:
/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/TTF/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/
Bug Mode: compatibility mode is disabled
DPMS (Energy Star):
Standby: 1200 Suspend: 1800 Off: 2400
DPMS is Enabled
Monitor is On
File paths:
Config file: /etc/X11/xorg.conf
Modules path: /usr/X11R6/lib/modules
Log file: /var/log/Xorg.0.log
OpenBSD 3.9 (GENERIC.MP) #598: Thu Mar 2 02:37:06 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Genuine Intel(R) CPU T2300 @ 1.66GHz ("GenuineIntel" 686-class) 1.67 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,EST,TM2
real mem = 1063428096 (1038504K)
avail mem = 963563520 (940980K)
using 4278 buffers containing 53272576 bytes (52024K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(54) BIOS, date 03/16/06, BIOS32 rev. 0 @ 0xfd4a0
pcibios0 at bios0: rev 2.1 @ 0xfd4a0/0xb60
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdd70/224 (12 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #5 is the last bus
bios0: ROM list: 0xc0000/0xe600! 0xce800/0x1800 0xdf000/0x1000! 0xe0000/0x1800!
mainbus0: Intel MP Specification (Version 1.4) (INTEL Napa ERB )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Enhanced SpeedStep 1000 MHz (1404 mV): unknown EST cpu, no changes
possible
cpu0: apic clock running at 166 MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Genuine Intel(R) CPU T2300 @ 1.66GHz ("GenuineIntel" 686-class) 1.67 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,EST,TM2
mainbus0: bus 0 is type PCI
mainbus0: bus 3 is type PCI
mainbus0: bus 10 is type PCI
mainbus0: bus 11 is type ISA
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 vendor "Intel", unknown product 0x27a0 rev 0x03
vga1 at pci0 dev 2 function 0 vendor "Intel", unknown product 0x27a2 rev 0x03:
aperture at 0xb0080000, size 0x8000000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
vendor "Intel", unknown product 0x27a6 (class display subclass miscellaneous,
rev 0x03) at pci0 dev 2 function 1 not configured
"Intel 82801GB HD Audio" rev 0x02 at pci0 dev 27 function 0 not configured
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x02
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x02
pci2 at ppb1 bus 2
"Intel PRO/Wireless 3945ABG" rev 0x02 at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x02
pci3 at ppb2 bus 3
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x02: apic 2 int 23
(irq 7)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x02: apic 2 int 19
(irq 11)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x02: apic 2 int 18
(irq 11)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x02: apic 2 int 16
(irq 11)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x02: apic 2 int 23
(irq 7)
ehci0: timed out waiting for BIOS
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe2
pci4 at ppb3 bus 4
cbb0 at pci4 dev 4 function 0 vendor "Texas Instruments", unknown product
0x8039 rev 0x00pci_intr_map: bus 4 dev 4 func 0 pin 1; line 11
pci_intr_map: no MP mapping found
: irq 11
vendor "Texas Instruments", unknown product 0x803a (class serial bus subclass
Firewire, rev 0x00) at pci4 dev 4 function 1 not configured
vendor "Texas Instruments", unknown product 0x803b (class mass storage subclass
miscellaneous, rev 0x00) at pci4 dev 4 function 2 not configured
vendor "Texas Instruments", unknown product 0x803c (class system unknown
subclass 0x05, rev 0x00) at pci4 dev 4 function 3 not configured
fxp0 at pci4 dev 8 function 0 "Intel PRO/100 VM" rev 0x02, i82562: apic 2 int
11 (irq 11), address 00:16:36:27:2b:4c
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 5 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x02: PM disabled
pciide0 at pci0 dev 31 function 2 vendor "Intel", unknown product 0x27c4 rev
0x02: DMA (unsupported), channel 0 wired to compatibility, channel 1 wired to
compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MHV2160BT>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GMA-4082N, HV02> SCSI0 5/cdrom
removable
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x02: apic 2 int 19
(irq 11)
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
biomask 0 netmask 0 ttymask 0
ioapic0: pin 11 shares different IPL interrupts (40..50), degraded performance
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
ugen0 at uhub2 port 1uhidev0 at uhub1 port 1 configuration 1 interface 0
ugen0: STMicroelectronics Biometric Coprocessor, rev 1.00/0.01, addr 2
uhidev0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev 1.10/3.00,
addr 2, iclass 3/1
ums0 at uhidev0: 5 buttons and Z dir.
wsmouse1 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
cpu1: Enhanced SpeedStep 1000 MHz (1404 mV): unknown EST cpu, no changes
possible
[demime 1.01d removed an attachment of type application/octet-stream which had
a name of Xorg.0.log]
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/TTF/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/CID/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "glx"
Load "record"
Load "xtrap"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "wsmouse"
Option "Device" "/dev/wsmouse"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "ShadowFB" # [<bool>]
#Option "DefaultRefresh" # [<bool>]
#Option "ModeSetClearScreen" # [<bool>]
Option "DPMS"
Identifier "Card0"
Driver "vesa"
VendorName "Intel Corporation"
BoardName "Mobile Integrated Graphics Controller"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
