Hi there, I have a question about a network card recently bought by one customer and which is shown as not configured in dmesg, and the board seems to have on the cd it came with drivers for win family, novell, linux and freebsd but not openbsd, so I am wondering if there is any chance to use it with openbsd 3.9 stable, and a second question to any of you, is there on openbsd an equivalent of linux's "lspci" ?
================= Dmesg output: OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III ("GenuineIntel" 686-class) 731 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE real mem = 132685824 (129576K) avail mem = 114339840 (111660K) using 1645 buffers containing 6737920 bytes (6580K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(7d) BIOS, date 04/11/01, BIOS32 rev. 0 @ 0xfd87d apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown apm0: flags 30102 dobusy 0 doidle 1 pcibios0 at bios0: rev 2.1 @ 0xfd810/0x7f0 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf30/176 (9 entries) pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00) pcibios0: PCI bus #1 is the last bus bios0: ROM list: 0xc0000/0xa000 0xe4000/0xc000! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 82815 Hub" rev 0x02 vga1 at pci0 dev 2 function 0 "Intel 82815 Graphics" rev 0x02: aperture at 0xf0000000, size 0x4000000 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02 pci1 at ppb0 bus 1 vendor "Sundance", unknown product 0x0200 (class network subclass ethernet, rev 0x31) at pci1 dev 1 function 0 not configured xl0 at pci1 dev 2 function 0 "3Com 3c905C 100Base-TX" rev 0x74: irq 9, address 00:01:02:dc:1a:46 bmtphy0 at xl0 phy 24: Broadcom 3C905C internal PHY, rev. 6 xl1 at pci1 dev 4 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 5, address 00:01:03:17:29:36 bmtphy1 at xl1 phy 24: Broadcom 3C905C internal PHY, rev. 7 ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02 pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: <ST310211A> wd0: 16-sector PIO, LBA, 9641MB, 19746720 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 pciide0: channel 1 disabled (no drives) uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 9 iic0 at ichiic0 isa0 at ichpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 lpt0 at isa0 port 0x378/4 irq 7 npx0 at isa0 port 0xf0/16: using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom0: console fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec biomask ff4d netmask ff6d ttymask ffef pctr: 686-class user-level performance counters enabled mtrr: Pentium Pro MTRR support dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 Thanks. -- Claudiu Pruna <[EMAIL PROTECTED]>