Hi,
this is curious. I've tried 3.9 SMP base kernel
(GENERIC) and found that my wireless card is supported,
but didn't work at all! As I took a closer look,
I figured out that it wasn't my network card,
it was something with the PCI or perhaps with the
BIOS<->PCI mapping. And than came the most curious,
I tried the `not SMP' (3.9 base GENERIC) kernel and it worked!!
(Using SMP `current' doesn't help either.)
Is this a known issue and if so is there someone working on this??
Thanks,
Paul Sonkoly
Here come my 2 dmesgs :
Note the `pci_intr_map: no MP mapping found' here.
OpenBSD 3.9 (GENERIC.MP) #598: Thu Mar 2 02:37:06 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class) 2.81 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
real mem = 536059904 (523496K)
avail mem = 482070528 (470772K)
using 4278 buffers containing 26906624 bytes (26276K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 06/21/05, BIOS32 rev. 0 @ 0xf0010
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7e10/304 (17 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GB LPC" rev 0x00)
pcibios0: PCI bus #4 is the last bus
bios0: ROM list: 0xc0000/0xd000
mainbus0: Intel MP Specification (Version 1.4) (INTEL )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 200 MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class) 2.81 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
mainbus0: bus 0 is type PCI
mainbus0: bus 1 is type PCI
mainbus0: bus 2 is type PCI
mainbus0: bus 3 is type PCI
mainbus0: bus 4 is type PCI
mainbus0: bus 5 is type ISA
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82945GP" rev 0x81
ppb0 at pci0 dev 1 function 0 "Intel 82945GP PCIE" rev 0x81
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon X600 (RV380)" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"ATI Radeon X600 (RV380) Sec" rev 0x00 at pci1 dev 0 function 1 not configured
"Intel 82801GB HD Audio" rev 0x01 at pci0 dev 27 function 0 not configured
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 3 "Intel 82801GB PCIE" rev 0x01
pci3 at ppb2 bus 3
skc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8053" rev 0x19pci_intr_map: bus
3 dev 0 func 0 pin 1; line 10
pci_intr_map: no MP mapping found
, Marvell Yukon-2 EC rev. A3 (0x2): irq 10
sk port A at skc0 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 2 int 20
(irq 5)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 2 int 17
(irq 6)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 2 int 18
(irq 3)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 2 int 19
(irq 10)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 2 int 20
(irq 5)
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb3 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
pci4 at ppb3 bus 4
ral0 at pci4 dev 1 function 0 "Ralink RT2561S" rev 0x00pci_intr_map: bus 4 dev
1 func 0 pin 1; line 11
pci_intr_map: no MP mapping found
: irq 11, address 00:16:b6:5d:ba:f1
ral0: MAC/BBP RT2661B, RF RT2527
"Philips SAA7134 TV" rev 0x01 at pci4 dev 2 function 0 not configured
"ITExpress IT8211F" rev 0x11 at pci4 dev 3 function 0 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <_NEC, DVD_RW ND-3540A, 1.01> SCSI0 5/cdrom
removable
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 2 int 23 (irq 5) for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <Maxtor 6L200M0>
wd0: 16-sector PIO, LBA48, 194481MB, 398297088 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1 at pciide1 channel 1 drive 0: <Maxtor 6V160E0>
wd1: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 2 int 23
(irq 5)
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: unknown Winbond chip (ID 0xa1)
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask 0 netmask 0 ttymask 0
pctr: user-level cycle counter enabled
apm0: disconnected
umass0 at uhub4 port 6 configuration 1 interface 0
umass0: Kingston DataTraveler 2.0, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2 0/direct
removable
sd0: 978MB, 978 cyl, 64 head, 32 sec, 512 bytes/sec, 2002944 sec total
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: IBM product 0x310b, rev 2.00/1.60, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
ulpt0 at uhub0 port 1 configuration 1 interface 0
ulpt0: Hewlett-Packard hp LaserJet 1010, rev 1.10/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
dkcsum: wd0 matches BIOS drive 0x80
wd1: no disk label
dkcsum: wd1 matches BIOS drive 0x81
dkcsum: sd0 matches BIOS drive 0x82
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
==============================================
OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class) 2.81 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,CNXT-ID
real mem = 536059904 (523496K)
avail mem = 482119680 (470820K)
using 4278 buffers containing 26906624 bytes (26276K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 06/21/05, BIOS32 rev. 0 @ 0xf0010
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7e10/304 (17 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GB LPC" rev 0x00)
pcibios0: PCI bus #4 is the last bus
bios0: ROM list: 0xc0000/0xd000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82945GP" rev 0x81
ppb0 at pci0 dev 1 function 0 "Intel 82945GP PCIE" rev 0x81
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon X600 (RV380)" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"ATI Radeon X600 (RV380) Sec" rev 0x00 at pci1 dev 0 function 1 not configured
"Intel 82801GB HD Audio" rev 0x01 at pci0 dev 27 function 0 not configured
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 3 "Intel 82801GB PCIE" rev 0x01
pci3 at ppb2 bus 3
skc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8053" rev 0x19, Marvell Yukon-2
EC rev. A3 (0x2): irq 10
sk port A at skc0 not configured
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: irq 6
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: irq 3
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: irq 10
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: irq 5
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb3 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
pci4 at ppb3 bus 4
ral0 at pci4 dev 1 function 0 "Ralink RT2561S" rev 0x00: irq 11, address
00:16:b6:5d:ba:f1
ral0: MAC/BBP RT2661B, RF RT2527
"Philips SAA7134 TV" rev 0x01 at pci4 dev 2 function 0 not configured
"ITExpress IT8211F" rev 0x11 at pci4 dev 3 function 0 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <_NEC, DVD_RW ND-3540A, 1.01> SCSI0 5/cdrom
removable
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide1: using irq 5 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <Maxtor 6L200M0>
wd0: 16-sector PIO, LBA48, 194481MB, 398297088 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1 at pciide1 channel 1 drive 0: <Maxtor 6V160E0>
wd1: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: irq 5
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: unknown Winbond chip (ID 0xa1)
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask f76d netmask ff6d ttymask ffef
pctr: user-level cycle counter enabled
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: IBM product 0x310b, rev 2.00/1.60, addr 2, iclass 3/1
ulpt0 at uhub0 port 1 configuration 1 interface 0ums0 at uhidev0: 3 buttons and
Z dir.
wsmouse0 at ums0 mux 0
ulpt0: Hewlett-Packard hp LaserJet 1010, rev 1.10/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
dkcsum: wd0 matches BIOS drive 0x80
wd1: no disk label
dkcsum: wd1 matches BIOS drive 0x81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
WARNING: / was not properly unmounted
umass0 at uhub4 port 6 configuration 1 interface 0
umass0: Kingston DataTraveler 2.0, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2 0/direct
removable
sd0: 978MB, 978 cyl, 64 head, 32 sec, 512 bytes/sec, 2002944 sec total
