On 1/31/07, Greg Thomas <[EMAIL PROTECTED]> wrote:
I'm getting random "unknown authentication state 1" and "device
timeout" messages with the built-in card on my T40.
Hi all,
I have similar problems with the iwi driver on my T43. I have the message :
iwi0: XXX too many rates (count=13, last=108)
And sometimes :
iwi0: fatal firmware error
and
iwi0: unknown authentication state 1
If I unplug the network cable, the trunk0 interface doesn't work
anymore (it doesn't switch to iwi). I like to have a trunk device with
bge and iwi as failover, but I saw the same without trunk.
The problem occurs with -current (not with 4.0).
Configuration details and dmesg follow :
[EMAIL PROTECTED]: ~ $ sudo ifconfig bge0 up
[EMAIL PROTECTED]: ~ $ sudo ifconfig iwi0 up nwid GOUTTEDELAINE chan 10
[EMAIL PROTECTED]: ~ $ sudo ifconfig trunk0 create
[EMAIL PROTECTED]: ~ $ sudo ifconfig trunk0 trunkproto failover trunkport
bge0 trunkport iwi0
[EMAIL PROTECTED]: ~ $ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkdev trunk0
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::211:25ff:fed3:542c%bge0 prefixlen 64 scopeid 0x1
iwi0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkdev trunk0
groups: wlan
media: IEEE802.11 autoselect
status: no network
ieee80211: nwid GOUTTEDELAINE chan 10 100dBm
inet6 fe80::212:f0ff:fedc:3d69%iwi0 prefixlen 64 scopeid 0x2
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33224
enc0: flags=0<> mtu 1536
trunk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkproto failover
trunkport iwi0
trunkport bge0 master,active
groups: trunk
media: Ethernet autoselect
status: active
[EMAIL PROTECTED]: ~ $ sudo ifconfig -M iwi0
******************
(the antenna light blink)
******************
[EMAIL PROTECTED]: ~ $ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkdev trunk0
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet6 fe80::211:25ff:fed3:542c%bge0 prefixlen 64 scopeid 0x1
iwi0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkdev trunk0
groups: wlan
media: IEEE802.11 autoselect
status: active
ieee80211: nwid GOUTTEDELAINE chan 10 bssid 00:09:5b:fe:0a:3a
87dB 100dBm
inet6 fe80::212:f0ff:fedc:3d69%iwi0 prefixlen 64 scopeid 0x2
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33224
enc0: flags=0<> mtu 1536
trunk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:11:25:d3:54:2c
trunk: trunkproto failover
trunkport iwi0
trunkport bge0 master,active
groups: trunk
media: Ethernet autoselect
status: active
[EMAIL PROTECTED]: ~ $ sudo dhclient trunk0
DHCPREQUEST on trunk0 to 255.255.255.255 port 67
DHCPACK from 172.16.4.254
bound to 172.16.1.49 -- renewal in 86400 seconds.
**************
OpenBSD 4.1-beta (GENERIC) #1371: Wed Feb 14 15:42:07 MST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1.86GHz ("GenuineIntel"
686-class) 1.87 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
real mem = 1072132096 (1047004K)
avail mem = 969854976 (947124K)
using 4256 buffers containing 53731328 bytes (52472K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 08/21/06, BIOS32 rev. 0 @
0xfd760, SMBIOS rev. 2.33 @ 0xe0010 (64 entries)
bios0: IBM 2668WEV
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 100%
apm0: AC on, battery charge high
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd6f0/0x910
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdeb0/256 (14 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #12 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1600 0xd1800/0x1000
0xdc000/0x4000! 0xe0000/0x10000
acpi at mainbus0 not configured
cpu0 at mainbus0
cpu0: Enhanced SpeedStep 1867 MHz (1308 mV): speeds: 1867, 1600, 1333,
1067, 800 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M300 M22" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03
pci2 at ppb1 bus 2
bge0 at pci2 dev 0 function 0 "Broadcom BCM5751M" rev 0x11, BCM5750 B1
(0x4101): irq 11, address 00:11:25:d3:54:2c
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
ppb2 at pci0 dev 28 function 2 "Intel 82801FB PCIE" rev 0x03
pci3 at ppb2 bus 3
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: irq 11
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: irq 11
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3
pci4 at ppb3 bus 11
cbb0 at pci4 dev 0 function 0 "Ricoh 5C476 CardBus" rev 0x8d: irq 11
iwi0 at pci4 dev 2 function 0 "Intel PRO/Wireless 2200BG" rev 0x05:
irq 11, address 00:12:f0:dc:3d:69
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 12 device 0 cacheline 0x0, lattimer 0xb0
pcmcia0 at cardslot0
auich0 at pci0 dev 30 function 2 "Intel 82801FB AC97" rev 0x03: irq
11, ICH6 AC97
ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801FB Modem" rev 0x03 at pci0 dev 30 function 3 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03: PM disabled
pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x03: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <HTS541080G9AT00>
wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, DVD-RAM UJ-822S, 1.61> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x03: irq 11
iic0 at ichiic0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
aps0 at isa0 port 0x1600/31
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask effd netmask effd ttymask ffff
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
umass0 at uhub4 port 3 configuration 1 interface 0
umass0: Maxtor OneTouch, rev 2.00/2.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <Maxtor, OneTouch, 0201> SCSI0 0/direct fixed
sd0: 194480MB, 194480 cyl, 64 head, 32 sec, 512 bytes/sec, 398295040 sec total
ugen0 at uhub2 port 2
ugen0: STMicroelectronics Biometric Coprocessor, rev 1.00/0.01, addr 2
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: Logitech USB-PS/2 Optical Mouse, rev 2.00/22.00, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse1 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: sd0 matches BIOS drive 0x81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
auich0: measured ac97 link rate at 48004 Hz, will use 48000 Hz
iwi0: XXX too many rates (count=13, last=108)
iwi0: XXX too many rates (count=13, last=108)
--
Mattieu Baptiste
"/earth is 102% full ... please delete anyone you can."
