i had a MegaRAID 300-8x adapter running with 2 disks (1 logical drive)
in a RAID1 from 3.8 until now. it has been working fine until yesterday
and is running 4.0-release.
i added 4x500 GB disks in hotswap trays that connect to a backplane
yesterday evening, then rebooted the machine, went into the RAID BIOS
for the adapter, configured the 4 disks as a ~1.4 TB RAID5 logical drive
and initialized it. i also checked that logical drive 1, the RAID1
array, was flagged as the bootable drive. now the machine won't boot,
despite my having done a consistency check on the RAID1 drive which
yielded no corrections.
after this the same problem persists: when booting it doesn't even
detect a disk to boot from and goes directly to PXE booting. i have not
yet tried to unconfigure/remove the new RAID5 drive to see if this fixes
the booting issue (will do this later tonight). since i can't get the
machine to boot, i haven't a up-to-date dmesg to concatenate, but this
is a dmesg from an earlier post i made about this same machine:
OpenBSD 3.8-current (GENERIC.MP) #338: Sat Oct 8 12:43:21 MDT
2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 1 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR,SSE
real mem = 268017664 (261736K)
avail mem = 237666304 (232096K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 04/23/03, BIOS32
rev. 0 @ 0xfdba0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown, estimated 0:00 hours
apm0: APM get event: interface not connected (3)
apm0: APM get event: interface not connected (3)
apm0: disconnected
apm0: flags 30102 dobusy 0 doidle 0
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf4b70/192 (10 entries)
pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks ROSB4
SouthBridge" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x2200 0xca800/0x1000
0xcb800/0x1000
ipmi at mainbus0 not configured
mainbus0: Intel MP Specification (Version 1.4) (AMI
CNB30LE )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 132 MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel Pentium III ("GenuineIntel" 686-class) 1 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR,SSE
mainbus0: bus 0 is type PCI
mainbus0: bus 1 is type PCI
mainbus0: bus 2 is type PCI
mainbus0: bus 3 is type ISA
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0: apid 9 pa 0xfec01000, version 11, 16 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x06
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x06
pci1 at pchb1 bus 1
ppb0 at pci1 dev 3 function 0 vendor "Intel", unknown product
0x0335 rev 0x07
pci2 at ppb0 bus 2
ami0 at pci2 dev 14 function 0 "Symbios Logic MegaRAID SATA
8x" rev 0x07: apic 9 int 7 (irq 10) LSI 3008/32b
ami0: FW 813G, BIOS vH425, 128MB RAM
ami0: 1 channels, 0 FC loops, 1 logical drives
scsibus0 at ami0: 40 targets
sd0 at scsibus0 targ 0 lun 0: <AMI, Host drive #00, > SCSI2
0/direct fixed
sd0: 189781MB, 189781 cyl, 64 head, 32 sec, 512 bytes/sec,
388671488 sec total
scsibus1 at ami0: 16 targets
vga1 at pci0 dev 1 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
fxp0 at pci0 dev 4 function 0 "Intel 82557" rev 0x08, i82559:
apic 9 int 4 (irq 9), address 00:e0:81:04:64:96
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci0 dev 5 function 0 "Intel 82557" rev 0x08, i82559:
apic 9 int 5 (irq 5), address 00:e0:81:04:64:97
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
pcib0 at pci0 dev 15 function 0 "ServerWorks ROSB4
SouthBridge" rev 0x50
pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev
0x00: DMA
atapiscsi0 at pciide0 channel 0 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <DELTA, OIP-SD2400A/BM, 5.6i>
SCSI0 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB"
rev 0x04: apic 8 int 10 (irq 10), version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask 0 netmask 0 ttymask 0
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
i'm pretty sure i'm running bsd and not bsd.mp at the moment, but can't be sure
without being able to boot it.
any advice is appreciated.
cheers,
jake
