Greetings,
I have just upgraded to 4.1 from 3.9 (via 4.0) and was looking
forward to my ral(4) hostap being able to operate in both 802.11b and
802.11g modes. I note, however, that my 802.11g capable client
[lladdr 00:11:09:17:35:24 in the output below] is still operating in
802.11b mode. Is mixed mode possible yet and if so, how?
Looking back now, the commit messages for sys/dev/ic/rt2560.c and
Damien Bergamini's comments in http://www.oreillynet.com/pub/a/
sysadmin/2006/10/26/openbsd-40.html seem to imply some of the
infrastructure has been put in place but perhaps not all of it yet?
Or have I misinterpreted?
# ifconfig -M ral0
ral0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:13:d3:6a:bb:9d
groups: wlan
media: IEEE802.11 autoselect hostap (autoselect mode 11b
hostap)
status: active
ieee80211: nwid THE_OFFICE chan 11 bssid 00:13:d3:6a:bb:9d
100dBm
lladdr 00:11:09:17:35:24 55dB 11M short_preamble assoc
lladdr 00:40:f4:aa:33:26 56dB 11M assoc
inet 192.168.1.1 netmask 0xfffffffc broadcast 192.168.1.3
inet6 fe80::213:d3ff:fe6a:bb9d%ral0 prefixlen 64 scopeid 0x2
inet 192.168.1.5 netmask 0xfffffffc broadcast 192.168.1.7
# cat /etc/hostname.ral0
inet 192.168.1.1 255.255.255.252 192.168.1.3 media autoselect \
mediaopt hostap nwid THE_OFFICE chan 11
inet alias 192.168.1.5 255.255.255.252 192.168.1.7
# dmesg
OpenBSD 4.1 (GENERIC) #0: Sat May 26 01:30:55 CST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache)
499 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
MMX,FXSR,SSE
real mem = 200773632 (196068K)
avail mem = 175529984 (171416K)
using 2481 buffers containing 10162176 bytes (9924K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 07/11/02, BIOS32 rev. 0 @
0xfd7b1, SMBIOS rev. 2.3 @ 0xf8386 (38 entries)
bios0: IBM 656345A
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf1e60/160 (8 entries)
pcibios0: PCI Interrupt Router at 000:02:0 ("VIA VT82C596A ISA" rev
0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa000 0xca000/0x1000
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0x82
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "S3 Savage 4" rev 0x03
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "VIA VT82C596A ISA" rev 0x12
pciide0 at pci0 dev 2 function 1 "VIA VT82C571 IDE" rev 0x06: ATA66,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MPE3136AH B4>
wd0: 16-sector PIO, LBA, 12949MB, 26520480 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <LG, CD-ROM CRD-8400B, 1.12> SCSI0 5/
cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 2 function 2 "VIA VT83C572 USB" rev 0x08: irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"VIA VT82C596 Power" rev 0x20 at pci0 dev 2 function 3 not configured
fxp0 at pci0 dev 14 function 0 "Intel 8255x" rev 0x08, i82559: irq 9,
address 00:04:ac:8b:51:11
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
ral0 at pci0 dev 15 function 0 "Ralink RT2560" rev 0x01: irq 5,
address 00:13:d3:6a:bb:9d
ral0: MAC/BBP RT2560 (rev 0x04), RF RT2525
esa0 at pci0 dev 18 function 0 "ESS ES1989" rev 0x10: irq 9
ac97: codec id 0x45838308 (ESS Technology ES1921)
ac97: codec features 20 bit DAC, 20 bit ADC, ESS Technology
audio0 at esa0
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask fd45 netmask ff65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
Any advice will be appreciated.
Thanks,
Damon
