Hi all, I installed successfull OpenBSD on my HP nx7010 (Intel Centrino) but I had a problem with the Intel PRO Wireless 2100 integrated card...
I saw the card but I can't use it and the message "cannot read firmware" appeared on the console and in dmesg output. I found this article: http://damien.bergamini.free.fr/ipw/ipw-openbsd.html that seem applies to my case and I followed the instructions (install firmware with pkg_add http://damien.bergamini.free.fr/ipwfw/OpenBSD/ipw-firmware-1.3.tgz) The problem of message "cannot read firmware" disappeared but when I take up the interface with "ifconfig ipw0 up" the OS freeze (only keyboard input is detected and displayed on screen, cannot switch to another tty,... just power off the lap-top) Does anyone know this issue and help me tracking the problem? What I'm wrong? Here above the output of dmesg after firmware install. If more informations needed, please ask me! Andrea ---------------------------------------------------------------------------------------------------------------------- OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel(R) Pentium(R) M processor 1600MHz ("GenuineIntel" 686-class) 1.60 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,EST,TM2 real mem = 1073115136 (1047964K) avail mem = 971776000 (949000K) using 4278 buffers containing 53780480 bytes (52520K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+ BIOS, date 11/17/03, BIOS32 rev. 0 @ 0xf0000, SMBIOS rev. 2.3 @ 0xfa1b6 (17 entries) bios0: Hewlett-Packard 0860 apm0 at bios0: Power Management spec V1.2 (BIOS managing devices) apm0: AC on, battery charge unknown apm0: flags 130102 dobusy 0 doidle 1 pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf0840/176 (9 entries) pcibios0: bad IRQ table checksum pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf99f0/176 (9 entries) pcibios0: PCI Exclusive IRQs: 5 10 11 pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801DBM LPC" rev 0x00) pcibios0: PCI bus #3 is the last bus bios0: ROM list: 0xc0000/0x10000 acpi at mainbus0 not configured cpu0 at mainbus0 cpu0: Enhanced SpeedStep 1600 MHz (1484 mV): speeds: 1600, 1400, 1200, 1000, 800, 600 MHz pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 82855PE Hub" rev 0x03 ppb0 at pci0 dev 1 function 0 "Intel 82855PE AGP" rev 0x03 pci1 at ppb0 bus 1 vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M9 Lf" rev 0x01 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 10 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 5 usb1 at uhci1: USB revision 1.0 uhub1 at usb1 uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 5 usb2 at uhci2: USB revision 1.0 uhub2 at usb2 uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 5 usb3 at ehci0: USB revision 2.0 uhub3 at usb3 uhub3: Intel EHCI root hub, rev 2.00/1.00, addr 1 uhub3: 6 ports with 6 removable, self powered ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x81 pci2 at ppb1 bus 2 "VIA VT6306 FireWire" rev 0x80 at pci2 dev 0 function 0 not configured re0 at pci2 dev 1 function 0 "Realtek 8139" rev 0x20: RTL8139C+ (0x7480), irq 10, address 00:02:3f:6a:75:cc rlphy0 at re0 phy 0: RTL internal PHY ipw0 at pci2 dev 2 function 0 "Intel PRO/Wireless 2100" rev 0x04: irq 11, address 00:0c:f1:09:a8:8a cbb0 at pci2 dev 4 function 0 "ENE CB-1410 CardBus" rev 0x01: irq 5 cardslot0 at cbb0 slot 0 flags 0 cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8, lattimer 0x20 pcmcia0 at cardslot0 ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x01 pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility wd0 at pciide0 channel 0 drive 0: <FUJITSU MHT2060AT PL> wd0: 16-sector PIO, LBA, 57231MB, 117210240 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 atapiscsi0 at pciide0 channel 1 drive 0 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <SONY, DVD+RW DW-P50A, 1.8e> SCSI0 5/cdrom removable cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x01: irq 10 iic0 at ichiic0 auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 10, ICH4 AC97 ac97: codec id 0x41445374 (Analog Devices AD1981B) ac97: codec features headphone, 20 bit DAC, No 3D Stereo audio0 at auich0 "Intel 82801DB Modem" rev 0x01 at pci0 dev 31 function 6 not configured isa0 at ichpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pmsi0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pmsi0 mux 0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 lpt0 at isa0 port 0x378/4 irq 7 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom2: irq 5 already in use biomask e76d netmask ef6d ttymask ffef pctr: 686-class user-level performance counters enabled mtrr: Pentium Pro MTRR support umass0 at uhub3 port 3 configuration 1 interface 0 umass0: Swissbit cirrusWHITE, rev 2.00/0.02, addr 2 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets sd0 at scsibus1 targ 1 lun 0: <Swissbit, cirrusWHITE, 2.00> SCSI0 0/direct removable sd0: 1933MB, 1933 cyl, 64 head, 32 sec, 512 bytes/sec, 3958784 sec total uhidev0 at uhub1 port 2 configuration 1 interface 0 uhidev0: Logitech USB-PS/2 Optical Mouse, rev 2.00/20.00, addr 2, iclass 3/1 ums0 at uhidev0: 3 buttons and Z dir. wsmouse1 at ums0 mux 0 ugen0 at uhub2 port 2 ugen0: ACTIONTEC Bluetooth by hp, rev 1.10/8.02, addr 2 dkcsum: wd0 matches BIOS drive 0x81 dkcsum: sd0 matches BIOS drive 0x80 root on sd0a rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
