On Wed, Jun 27, 2007 at 09:45:17PM -0400, Eric wrote:
hello..
i just installed OpenBSD 4.1 from an original CD. My USB ethernet adapter,
a Linksys USB200M is a known good working adapter (verified on Mac OS X
10.4 and FreeBSD 6.2). I am building a gateway with OpenBSD and this
hardware has only one builtin ethernet adapter (rl0) and will require a
2nd. PCI ethernet is not an option (it's a small form factor fanless PC).
I require the USB200M to operate or a suitable alternative must be found.
<snipped - full dmesg below>
The documentation confirms the USB200M is supported via the axe(4) driver.
The FAQ, mailing list archives, and google have produced no answers. They
seem to produce results stating either that the USB200M is supported via
axe(4) or that the axe(4) driver has been committed (in the 3.x branches).
Almost all of the available information is relating to the introduction of
axe(4) in 3.x. Some results refer to this issue, but have no replies which
resolve the problem.
I can't tell if you have a USB2 (ehci) controller, you didn't
include a full dmesg.
But if you don't perhaps there is an issue with usb/uhci code
not properly handling high speed devices on low speed controllers.
The BIOS has an option for "OnChip USB2" which is enabled, as
is "OnChip USB". However i don't see a ehci controller
Full dmesg:
OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: VIA Samuel 2 ("CentaurHauls" 686-class) 802 MHz
cpu0: FPU,DE,TSC,MSR,MTRR,PGE,MMX
real mem = 125337600 (122400K)
avail mem = 106831872 (104328K)
using 1560 buffers containing 6389760 bytes (6240K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 03/17/03, BIOS32 rev. 0 @ 0xfb390,
SMBIOS rev. 2.2 @ 0xf0800 (43 entries)
bios0: VIA Technologies, Inc. VT8601
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdd54
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdce0/112 (5 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11 12
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xcc000/0x4000! 0xd0000/0x4000
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8601 PCI" rev 0x05
ppb0 at pci0 dev 1 function 0 "VIA VT82C601 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "Trident CyberBlade i1" rev 0x6a
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-8192>
wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x1a: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x1a: irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x40
rl0 at pci0 dev 14 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:11:5b:01:e8:74
rlphy0 at rl0 phy 0: RTL internal PHY
cmpci0 at pci0 dev 15 function 0 "C-Media Electronics CMI8738/C3DX Audio"
rev 0x10: irq 12
audio0 at cmpci0
opl0 at cmpci0: model OPL3
midi0 at opl0: <CMPCI Yamaha OPL3>
mpu at cmpci0 not configured
"C-Media Electronics HSP56 AMR" rev 0x20 at pci0 dev 15 function 1 not
configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask ef6d netmask ef6d ttymask efef
pctr: user-level cycle counter enabled
uhub0: port 1, set config at addr 2 failed
uhub0: device problem, disabling port 1
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
thank you
