4.1-current fresed yesterday. see attached dmesg after boot.
in GENERIC ACPIVERBOSE and ACPI_ENABLE enabled.
if i turn off the notebook and turn it on again it sees the battery, but
the model is not read correctly (should be M6V) and there are no useful
info about it:
# sysctl -a | grep ^hw\.sensors
hw.sensors.acpibat0.volt0=unknown (voltage), UNKNOWN
hw.sensors.acpibat0.volt1=unknown (current voltage), UNKNOWN
hw.sensors.acpibat0.amphour0=unknown (last full capacity), UNKNOWN
hw.sensors.acpibat0.amphour1=4294.97 Ah (warning capacity)
hw.sensors.acpibat0.amphour2=4294.97 Ah (low capacity)
hw.sensors.acpibat0.amphour3=unknown (remaining capacity), UNKNOWN
hw.sensors.acpibat0.raw0=unknown (battery unknown), UNKNOWN
hw.sensors.acpibat0.raw1=unknown (rate), UNKNOWN
hw.sensors.acpibat1.volt0=unknown (voltage), UNKNOWN
hw.sensors.acpibat1.volt1=unknown (current voltage), UNKNOWN
hw.sensors.acpibat1.amphour0=unknown (last full capacity), UNKNOWN
hw.sensors.acpibat1.amphour1=4294.97 Ah (warning capacity)
hw.sensors.acpibat1.amphour2=4294.97 Ah (low capacity)
hw.sensors.acpibat1.amphour3=unknown (remaining capacity), UNKNOWN
hw.sensors.acpibat1.raw0=unknown (battery unknown), UNKNOWN
hw.sensors.acpibat1.raw1=unknown (rate), UNKNOWN
i have just one battery, so acpibat1 should be ignored.
if i just reset the notebook without a poweroff then there are no
batteries seen at all.
other mistery:
if i make a halt -p then somtimes the machine is powered off and
sometimes it is powered off but after 1-2 secs it is powered on again.
strange ah?
i really don't care about the halt -p but to see the battery's state is
important. i don't like to fly with closed eyes.
please give me vectors how i could solve this problem?
thank you
bdz
OpenBSD 4.1-current (GENERIC) #1: Thu Jun 28 18:29:46 GMT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1.73GHz ("GenuineIntel" 686-class) 1.73
GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
real mem = 1073049600 (1023MB)
avail mem = 1029996544 (982MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 06/08/05, BIOS32 rev. 0 @ 0xf0010, SMBIOS
rev. 2.3 @ 0xf8dd0 (36 entries)
bios0: ASUSTeK Computer Inc. M6V
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf4750/272 (15 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FB LPC" rev 0x00)
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0x10000
acpi0 at mainbus0: rev 0
acpi0: tables DSDT FACP APIC MCFG OEMB SSDT
acpitimer at acpi0 not configured
acpi device at acpi0 from table DSDT not configured
acpi device at acpi0 from table FACP not configured
acpi device at acpi0 from table APIC not configured
acpi device at acpi0 from table MCFG not configured
acpi device at acpi0 from table OEMB not configured
acpi device at acpi0 from table SSDT not configured
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 3 (P0P3)
acpiprt2 at acpi0: bus 1 (P0P1)
acpiprt3 at acpi0: bus 0 (P0P4)
acpiprt4 at acpi0: bus 0 (P0P5)
acpiprt5 at acpi0: bus 0 (P0P6)
acpiprt6 at acpi0: bus 0 (P0P7)
acpiec at acpi0 not configured
acpicpu at acpi0 not configured
acpitz at acpi0 not configured
acpiac at acpi0 not configured
acpibat0 at acpi0: BAT0: model: \M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^? serial:
type: LIon oem: ASUSTEK
acpibat1 at acpi0: BAT1: model: \M^?\M^?\M^?\M^?\M^?\M^?\M^?\M^? serial:
type: LIon oem: ASUSTEK
acpibtn at acpi0 not configured
acpibtn at acpi0 not configured
cpu0 at mainbus0
cpu0: unknown Enhanced SpeedStep CPU, msr 0x06120d2606000d26
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 1733 MHz (1308 mV): speeds: 1733, 800 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03
pci1 at ppb0 bus 3
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility X600" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
azalia0 at pci0 dev 27 function 0 "Intel 82801FB HD Audio" rev 0x04: irq 5
azalia0: host: High Definition Audio rev. 1.0
azalia0: codec: Realtek ALC880 (rev. 5.0), HDA version 0.9
azalia0: codec: 0x14f1/0x2bfa (rev. 0.0), HDA version 0.9
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1]: No audio function groups
audio0 at azalia0
uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: irq 4
uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: irq 5
uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: irq 6
uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: irq 5
ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: irq 4
usb0 at ehci0: USB revision 2.0
uhub0 at usb0: Intel EHCI root hub, rev 2.00/1.00, addr 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
pci2 at ppb1 bus 1
skc0 at pci2 dev 0 function 0 "Marvell Yukon 88E8001/8003/8010" rev 0x13, Yukon
Lite (0x9): irq 6
sk0 at skc0 port A: address 00:13:d4:9f:c5:ba
eephy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
cbb0 at pci2 dev 1 function 0 "Ricoh 5C476 CardBus" rev 0xb3: irq 5
"Ricoh 5C552 Firewire" rev 0x08 at pci2 dev 1 function 1 not configured
sdhc0 at pci2 dev 1 function 2 "Ricoh 5C822 SD/MMC" rev 0x17: irq 6
sdmmc0 at sdhc0
"Ricoh 5C592 Memory Stick" rev 0x08 at pci2 dev 1 function 3 not configured
"Ricoh 5C852 xD" rev 0x03 at pci2 dev 1 function 4 not configured
iwi0 at pci2 dev 2 function 0 "Intel PRO/Wireless 2915ABG" rev 0x05: irq 5,
address 00:12:f0:7d:60:b6
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x40
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <HTS541060G9AT00>
wd0: 16-sector PIO, LBA48, 57231MB, 117210240 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CD/DVDW TS-L532A, TC51> SCSI0 5/cdrom
removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
usb1 at uhci0: USB revision 1.0
uhub1 at usb1: Intel UHCI root hub, rev 1.00/1.00, addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2: Intel UHCI root hub, rev 1.00/1.00, addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3: Intel UHCI root hub, rev 1.00/1.00, addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4: Intel UHCI root hub, rev 1.00/1.00, addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask ef75 netmask ef75 ttymask fff7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: vendor 0x04d9 product 0x1400, rev 1.10/1.42, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1
uhidev1: vendor 0x04d9 product 0x1400, rev 1.10/1.42, addr 2, iclass 3/1
uhidev1: 3 report ids
ums0 at uhidev1 reportid 1: 5 buttons and Z dir.
wsmouse1 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=3, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
uhidev2 at uhub1 port 2 configuration 1 interface 0
uhidev2: Logitech Optical USB Mouse, rev 2.00/3.40, addr 3, iclass 3/1
ums1 at uhidev2: 3 buttons and Z dir.
wsmouse2 at ums1 mux 0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b
