i'm trying to get a ds9490r# to work on a soekris4801 with 4.1 but it
doesn't seem to get recognize (not depending on what is connected on the
1wire bus, even if nothing.
get:
uhub0: device problem, disabling port 1
nothing in sysctl hw.sensors for it.
any ideads to get it work ?
thanks a lot
Regards
Julien
OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133787648 (130652K)
avail mem = 114675712 (111988K)
using 1663 buffers containing 6811648 bytes (6652K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 20/40/12, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c3:58:cc
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c3:58:cd
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 10,
address 00:00:24:c3:58:ce
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 1: <CF 1GB>
wd0: 1-sector PIO, LBA, 967MB, 1981728 sectors
wd0(pciide0:0:1): using PIO mode 4, DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6 revision 3
wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, version
1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask fbe5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
uhub0: device problem, disabling port 1
