Hi,
I installed newest snapshot and I'm using kernel pppoe.
Sometimes the operator I'm connecting to doesn't authenticate
the pppoe requests and it can take a while, normally
it becomes connected in less than five minutes but
sometimes manual interference with the crappy dsl boxes
is required.
My question is, is the rc procedure supposed to hang
until the connection is established?
I pressed ^T to see what it is doing and I saw
ntpd there and nothing else. I tried to shut it
down with ^C, saw sh [pause] and soon after
the ntpd was back.
The rc scripts resumed to load right after the connection
had been established.
This is the uniprocessor dmesg, I'm normally using bsd.mp
but it's broken right now..
OpenBSD 4.3 (GENERIC) #696: Thu Mar 6 05:09:01 MST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 865 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 536375296 (511MB)
avail mem = 510599168 (486MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 03/05/99, BIOS32 rev. 0 @ 0xec7e0, SMBIOS
rev. 2.3 @ 0xfb378 (61 entries)
bios0: vendor Compaq version "686J4 v3.05" date 04/10/2001
bios0: Compaq Professional Workstation SP750
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC SSDT SSDT SSDT SSDT
acpi0: wakeup devices HUB_(S4) COM1(S4) COM2(S4) USB0(S1) PCI0(S4) PBTN(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (BUS1)
acpiprt2 at acpi0: bus 4 (HUB_)
acpiprt3 at acpi0: bus 3 (BUS3)
acpicpu0 at acpi0
acpibtn0 at acpi0: PBTN
bios0: ROM list: 0xc0000/0x9c00 0xc9c00/0x1800 0xcb400/0x5e00 0xd1200/0x4400
0xe0000/0x10000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82840 Host" rev 0x01
agp0 at pchb0: aperture at 0xec000000, size 0x2000000
ppb0 at pci0 dev 1 function 0 "Intel 82840 AGP" rev 0x01
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "Intergraph Expert3D" rev 0x64
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Intergraph Expert3D" rev 0x01 at pci1 dev 0 function 1 not configured
ppb1 at pci0 dev 2 function 0 "Intel 82840 PCI" rev 0x01
pci2 at ppb1 bus 2
ppb2 at pci2 dev 31 function 0 "Intel 82806AA" rev 0x02
pci3 at ppb2 bus 3
"Intel 82806AA APIC" rev 0x01 at pci3 dev 0 function 0 not configured
ppb3 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
pci4 at ppb3 bus 4
fxp0 at pci4 dev 2 function 0 "Intel 8255x" rev 0x08, i82559: irq 11, address
00:50:8b:cd:cd:79
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
ahc0 at pci4 dev 7 function 0 "Adaptec AIC-7899 U160" rev 0x01: irq 11
scsibus0 at ahc0: 16 targets
sd0 at scsibus0 targ 4 lun 0: <SEAGATE, ST336706LW, 0108> SCSI3 0/direct fixed
sd0: 35003MB, 26302 cyl, 4 head, 681 sec, 512 bytes/sec, 71687370 sec total
ahc1 at pci4 dev 7 function 1 "Adaptec AIC-7899 U160" rev 0x01: irq 11
scsibus1 at ahc1: 16 targets
xl0 at pci4 dev 10 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 11,
address 00:04:75:ca:2b:94
exphy0 at xl0 phy 24: 3Com internal media interface
pciide0 at pci4 dev 11 function 0 "CMD Technology SiI3112 SATA" rev 0x02: DMA
pciide0: using irq 11 for native-PCI interrupt
pciide0: port 0: device present, speed: 1.5Gb/s
wd0 at pciide0 channel 0 drive 0: <ST3200826AS>
wd0: 16-sector PIO, LBA48, 190782MB, 390721968 sectors
wd0(pciide0:0:0): using BIOS timings, Ultra-DMA mode 6
ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02
pciide1 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
pciide1: channel 0 disabled (no drives)
atapiscsi0 at pciide1 channel 1 drive 1
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <LITE-ON, LTR-52327S, QS04> SCSI0 5/cdrom
removable
cd0(pciide1:1:1): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 11
ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 11
iic0 at ichiic0
admtemp0 at iic0 addr 0x18: adm1021
admtemp1 at iic0 addr 0x1a: adm1021
thmc0 at iic0 addr 0x2e: thmc50
auich0 at pci0 dev 31 function 5 "Intel 82801AA AC97" rev 0x02: irq 11, ICH AC97
ac97: codec id 0x41445340 (Analog Devices AD1881)
ac97: codec features headphone, Analog Devices Phat Stereo
audio0 at auich0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask fd65 netmask fd65 ttymask ffe7
mtrr: Pentium Pro MTRR support
softraid0 at root
ahc0: target 4 using 16bit transfers
ahc0: target 4 synchronous at 80.0MHz DT, offset = 0x3f
root on sd0a swap on sd0b dump on sd0b
pppoe0: pap failure
pppoe0: pap failure
pppoe0: pap failure
pppoe0: pap failure
pppoe0: pap failure
pppoe0: pap failure
pppoe0: pap failure
