Hi all, this is my 1st post here. Here's a brief description about my
system:
Athlon 3500+ s939
DFi LP RDX200 CF-DR motherboard
GeCube Radeon HD2600 PCIe
Built-in Realtek HD Audio
WD400 40Gb ATA - 27Gb xp, 12Gb OpenBSD 4.3 AMD64
GAG4.9 Boot Manager
I've installed the 4.3 AMD64 successfully. The layout is:
/ - 128M
swap - 512M
/usr - rest
/tmp - 512M
/var - 1G
When 4.3 is probing devices on booting, I notice that the probe displayed
"Ati EHCI root hub" then my LCD monitor went standby, the monitor's LED
turned orange and the pc rebooted back to POST. I tried booting with ACPI
disabled but the problem got worst, pressing RESET and POWER button does
nothing and I had to turn off the power from the plug. I tried "UKC>
verbose" but the display is too fast to catch anything. I managed to get a
dmesg, but only using 4.3 i386 CD. Here's the dmesg:
-- dmesg --
OpenBSD 4.3 (RAMDISK_CD) #645: Wed Mar 12 11:31:03 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: AMD Athlon(tm) 64 Processor 3500+ ("AuthenticAMD" 686-class, 512KB L2
cache) 2.20 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2
real mem = 1072197632 (1022MB)
avail mem = 1030582272 (982MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/23/05, BIOS32 rev. 0 @ 0xfaa60,
SMBIOS rev. 2.3 @ 0xf0000 (47 entries)
bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 12/23/2005
apm0 at bios0: Power Management spec V1.2
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xcf74
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfce00/352 (20 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 21 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 3 5 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xee00 0xd0000/0x4000! 0xd4000/0x1000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ATI RS480 Host" rev 0x01
ppb0 at pci0 dev 2 function 0 "ATI RX480 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon HD 2600" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
"ATI Radeon HD 2600 HD Audio" rev 0x00 at pci1 dev 0 function 1 not
configured
ppb1 at pci0 dev 4 function 0 "ATI RS480 PCIE" rev 0x00
pci2 at ppb1 bus 2
mskc0 at pci2 dev 0 function 0 "Marvell Yukon 88E8053" rev 0x19, Yukon-2 EC
rev. A2 (0x1): irq 3
msk0 at mskc0 port A: address 00:01:29:d3:79:27
eephy0 at msk0 phy 0: Marvell 88E1111 Gigabit PHY, rev. 2
pciide0 at pci0 dev 17 function 0 "ATI IXP400 SATA" rev 0x80: DMA
pciide0: using irq 11 for native-PCI interrupt
pciide1 at pci0 dev 18 function 0 "ATI IXP400 SATA" rev 0x80: DMA
pciide1: using irq 10 for native-PCI interrupt
ohci0 at pci0 dev 19 function 0 "ATI IXP400 USB" rev 0x80: irq 3, version
1.0, legacy support
ohci1 at pci0 dev 19 function 1 "ATI IXP400 USB" rev 0x80: irq 3, version
1.0, legacy support
ehci0 at pci0 dev 19 function 2 "ATI IXP400 USB2" rev 0x80: irq 3
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
"ATI IXP400 SMBus" rev 0x81 at pci0 dev 20 function 0 not configured
pciide2 at pci0 dev 20 function 1 "ATI IXP400 IDE" rev 0x80: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide2 channel 0 drive 0: <WDC WD400BB-00FJA0>
wd0: 16-sector PIO, LBA, 38166MB, 78165360 sectors
wd1 at pciide2 channel 0 drive 1: <WDC WD200EB-11BHF0>
wd1: 16-sector PIO, LBA, 19092MB, 39102336 sectors
wd0(pciide2:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
wd1(pciide2:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
atapiscsi0 at pciide2 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CD/DVDW SH-S182D, SB05> SCSI0
5/cdrom removable
cd0(pciide2:1:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
"ATI IXP450 HD Audio" rev 0x01 at pci0 dev 20 function 2 not configured
pcib0 at pci0 dev 20 function 3 "ATI IXP400 ISA" rev 0x80
ppb2 at pci0 dev 20 function 4 "ATI IXP400 PCI" rev 0x80
pci3 at ppb2 bus 3
pciide3 at pci3 dev 8 function 0 "CMD Technology SiI3114 SATA" rev 0x02: DMA
pciide3: using irq 11 for native-PCI interrupt
"VIA VT6306 FireWire" rev 0x80 at pci3 dev 9 function 0 not configured
skc0 at pci3 dev 10 function 0 "Marvell Yukon 88E8001/8003/8010" rev 0x13,
Yukon Lite (0x9): irq 5
sk0 at skc0 port A: address 00:01:29:d3:78:f5
eephy1 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
pchb1 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ffcd netmask ffed ttymask ffef
rd0: fixed, 3800 blocks
uhidev0 at uhub1 port 1 configuration 1 interface 0 "vendor 0x15d9 USB
Mouse" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
uhid at uhidev0 not configured
root on rd0a swap on rd0b dump on rd0b
-- End of dmesg --
Is there anything that I can do about this? I won't mind installing i386 but
if there's a way to make this AMD64 version work, I'm all ears fer it.
Thanks in advace.
--
Karl
