It's 80-wire,but problem solved.My problem under OpenBSD was bad CD :-] Under Mandriva 2008.1 it was combination of new kernel and setup of BIOS, Which was then fighting with kernel :-/
Thanks a lot -----Original Message----- From: Sviatoslav Chagaev [mailto:[EMAIL PROTECTED] Sent: Saturday, August 02, 2008 10:54 PM To: Tomas Bodzar Subject: Re: Problem with CD/DVD RW - only read What IDE cable for this drive? 40- or 80-wire? A month or two ago, I was experiencing problems with my DVD-RW drive, it wouldn't read CDs/DVDs, outputing similar errors into dmesg. Then I replaced the 40-wire cable with an 80-wire one and all the problems disappeared. On Thu, 31 Jul 2008 06:31:33 +0100 Tomas Bodzar <[EMAIL PROTECTED]> wrote: > Hi all, > > Do you know someone what does mean this error? > > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5cd0/192 (10 entries) > cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4163B, A103> SCSI0 5/cdrom > removable > cd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 2 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5cd0/192 (10 entries) > cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4163B, A103> SCSI0 5/cdrom > removable > cd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 2 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x28 > > Mechanic was running fine for 4 years.Reads very well all types of supported > media. > I tried wodim in Mandriva 2008.1 sometimes error,that I must use TAO,sometimes > error > That buffer overflow and some others.K3b have no info during process about > Buffer, > but in setup or in info is everything OK for HW,SW and privileges.Forgot > dmesg, > but it shows buffer right.Than i reboot to OpenBSD and tried cdio and cdrtools > - nothing. > > Will it be sw problem or is mechanic dead?Can I use some of OpenBSD programs > for check condition? > Cdrtools shows mechanic,some info from it and from disc too.hdparm on Mandriva > shows no problem. > > Thanks a lot > > TB
