On Fri, 12 Sep 2008 11:51:40 +0300
"Denis Doroshenko" <[EMAIL PROTECTED]> wrote:
> hi,
>
> On Thu, Sep 11, 2008 at 3:45 PM, Miod Vallat <[EMAIL PROTECTED]>
> wrote:
> > CVSROOT: /cvs
> > Module name: src
> > Changes by: [EMAIL PROTECTED] 2008/09/11 06:45:20
> >
> > Modified files:
> > sys/dev/acpi : acpitz.c
> >
> > Log message:
> > Thermal Zone entities might not be direct object references, but
> > named references. Account for this, and the hp530 laptop won't
> > spontaneously power down thinking internal temperature is over 500C.
> >
> > ok marco@
>
> in a hope this diff would fix overheating under ACPI on my compaq
> nc6000, built the kernel and found out that this diff changed acpitz
> warnings from:
>
> acpitz0: _AL1[0] not a object ref
> acpitz0: _AL2[0] not a object ref
> acpitz0: _AL3[0] not a object ref
>
> to
>
> acpitz0: _AL1[0.0] _PRO not a package
> acpitz0: _AL2[0.0] _PRO not a package
> acpitz0: _AL3[0.0] _PRO not a package
>
Hi,
running the snapshot from the weekend (2008-09-22) on my HP nc6400
doesn't show the above mentioned console output anymore. Getting one
step closer to run OpenBSD on the notebook. Thanks.
Below the hw.sensors output which looks fine and the dmesg.
Sven
hw.sensors.acpitz0.temp0=45.05 degC (zone temperature)
hw.sensors.acpitz1.temp0=39.05 degC (zone temperature)
hw.sensors.acpitz2.temp0=37.05 degC (zone temperature)
hw.sensors.acpitz3.temp0=23.85 degC (zone temperature)
hw.sensors.acpitz4.temp0=20.05 degC (zone temperature)
hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
hw.sensors.acpibat0.volt1=12.49 VDC (current voltage)
hw.sensors.acpibat0.amphour0=4.43 Ah (last full capacity)
hw.sensors.acpibat0.amphour1=0.22 Ah (warning capacity)
hw.sensors.acpibat0.amphour2=0.04 Ah (low capacity)
hw.sensors.acpibat0.amphour3=3.88 Ah (remaining capacity), OK
hw.sensors.acpibat0.raw0=2 (battery charging), OK
hw.sensors.acpibat0.raw1=1034 (rate)
hw.sensors.acpiac0.indicator0=On (power supply)
hw.sensors.cpu0.temp0=43.00 degC
OpenBSD 4.4-current (GENERIC.MP) #878: Sat Sep 20 14:12:25 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Genuine Intel(R) CPU T2400 @ 1.83GHz ("GenuineIntel" 686-class)
1.83 GHz cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,VMX,EST,TM2,xTPR
real mem = 3614863360 (3447MB) avail mem = 3508621312 (3346MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 09/05/07, BIOS32 rev. 0 @
0xf0000, SMBIOS rev. 2.4 @ 0xf398f (23 entries) bios0: vendor
Hewlett-Packard version "68YCU Ver. F.0B" date 09/05/2007 bios0:
Hewlett-Packard HP Compaq nc6400 (RA270AA#ABD) acpi0 at bios0: rev 2
acpi0: tables DSDT FACP SLIC HPET APIC MCFG TCPA SSDT SSDT SSDT SSDT
SSDT acpi0: wakeup devices C098(S5) C0F7(S3) C0F8(S3) C0F9(S3) C0FA(S3)
C101(S0) C229(S0) C111(S5) C234(S5) C117(S5) C235(S5) acpitimer0 at
acpi0: 3579545 Hz, 24 bits acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 166MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Genuine Intel(R) CPU T2400 @ 1.83GHz ("GenuineIntel" 686-class)
1.83 GHz cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,VMX,EST,TM2,xTPR
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins ioapic0:
duplicate apic id, remapped to apid 2 acpiprt0 at acpi0: bus 2 (C098)
acpiprt1 at acpi0: bus 8 (C101)
acpiprt2 at acpi0: bus 16 (C111)
acpiprt3 at acpi0: bus 32 (C117)
acpiprt4 at acpi0: bus 0 (C002)
acpiec0 at acpi0
acpicpu0 at acpi0
acpicpu1 at acpi0
acpitz0 at acpi0: critical temperature 256 degC
acpitz1 at acpi0: critical temperature 105 degC
acpitz2 at acpi0: critical temperature 105 degC
acpitz3 at acpi0: critical temperature 105 degC
acpitz4 at acpi0: critical temperature 110 degC
acpibat0 at acpi0: C1B4 model "Primary" serial 14908 2007/01/24 type
LIon oem "Hewlett-Packard" acpibat1 at acpi0: C1B3 not present
acpiac0 at acpi0: AC unit online
acpibtn0 at acpi0: C249
acpibtn1 at acpi0: C241
acpivideo at acpi0 not configured
bios0: ROM list: 0xc0000/0x10000!
cpu0: unknown Enhanced SpeedStep CPU, msr 0x06130b2c06000b2c
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 1833 MHz (1404 mV): speeds: 1833, 1000 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82945GM Host" rev 0x03
vga1 at pci0 dev 2 function 0 "Intel 82945GM Video" rev 0x03
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
agp0 at vga1: aperture at 0xe0000000, size 0x10000000
"Intel 82945GM Video" rev 0x03 at pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x01:
apic 2 int 16 (irq 10) azalia0: codec[s]: Analog Devices/0x1981,
AT&T/Lucent/0x3026, using Analog Devices/0x1981 audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 2
int 16 (irq 10) pci1 at ppb0 bus 8
bge0 at pci1 dev 0 function 0 "Broadcom BCM5753M" rev 0x21, BCM5750 C1
(0x4201): apic 2 int 16 (irq 10), address 00:16:d4:0d:67:3e brgphy0 at
bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0 ppb1 at pci0 dev 28
function 1 "Intel 82801GB PCIE" rev 0x01: apic 2 int 17 (irq 10) pci2
at ppb1 bus 16 wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless
3945ABG" rev 0x02: apic 2 int 17 (irq 10), MoW2, address
00:13:02:51:b4:19 ppb2 at pci0 dev 28 function 3 "Intel 82801GB PCIE"
rev 0x01: apic 2 int 19 (irq 5) pci3 at ppb2 bus 32 uhci0 at pci0 dev
29 function 0 "Intel 82801GB USB" rev 0x01: apic 2 int 20 (irq 10)
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 2
int 22 (irq 11) uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev
0x01: apic 2 int 18 (irq 11) uhci3 at pci0 dev 29 function 3 "Intel
82801GB USB" rev 0x01: apic 2 int 19 (irq 5) ehci0 at pci0 dev 29
function 7 "Intel 82801GB USB" rev 0x01: apic 2 int 20 (irq 10) usb0 at
ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev
2.00/1.00 addr 1 ppb3 at pci0 dev 30 function 0 "Intel 82801BAM
Hub-to-PCI" rev 0xe1 pci4 at ppb3 bus 2 cbb0 at pci4 dev 6 function 0
"TI PCIXX12 CardBus" rev 0x00: apic 2 int 18 (irq 11) "TI PCIXX12
Multimedia Card Reader" rev 0x00 at pci4 dev 6 function 2 not
configured sdhc0 at pci4 dev 6 function 3 "TI PCIXX12 Secure Data" rev
0x00: apic 2 int 22 (irq 11) sdmmc0 at sdhc0 "TI PCIXX12 Smart Card"
rev 0x00 at pci4 dev 6 function 4 not configured cardslot0 at cbb0 slot
0 flags 0 cardbus0 at cardslot0: bus 3 device 0 cacheline 0x10,
lattimer 0x20 pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x01: PM
disabled pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev
0x01: DMA, channel 0 configured to compatibility, channel 1 configured
to compatibility atapiscsi0 at pciide0 channel 0 drive 0 scsibus0 at
atapiscsi0: 2 targets, initiator 7 cd0 at scsibus0 targ 0 lun 0:
<MATSHITA, UJDA775 DVD/CDRW, 1.00> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 pciide0: channel 1
ignored (disabled) ahci0 at pci0 dev 31 function 2 "Intel 82801GBM
AHCI" rev 0x01: apic 2 int 21 (irq 10), AHCI 1.1 scsibus1 at ahci0: 32
targets, initiator 32 sd0 at scsibus1 targ 0 lun 0: <ATA,
HTS541080G9SA00, MB4O> SCSI3 0/direct fixed sd0: 76319MB, 512
bytes/sec, 156301488 sec total usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
ugen0 at uhub2 port 1 "AuthenTec Fingerprint Sensor" rev 1.10/6.21 addr
2 ugen1 at uhub1 port 1 "Broadcom Corp HP Integrated Module" rev
2.00/1.00 addr 2 softraid0 at root
root on sd0a swap on sd0b dump on sd0b
