I've got a Compaq DL380 with a Smart Array 5300 (ciss), with four drives
set up as a RAID 5 with hot spare. The array was configured using the
card's BIOS utility.
It appears one of the drives has failed, but the array hasn't rebuilt
using the hot spare. Any ideas if this is an OpenBSD issue or a Compaq
issue?
sysctl hw.sensors:
hw.sensors.ciss0.drive0=online (sd0), OK
bioctl -i ciss0
Volume Status Size Device
ciss0 0 Online 72829501440 sd0 RAID5
0 Online 36419584000 0:0.0 noencl <COMPAQ BD03685A24 >
1 Online 36419584000 0:1.0 noencl <COMPAQ BD03685A24 >
2 Failed 0 0:2.0 noencl <>
3 Hot spare 36419584000 0:3.0 noencl <COMPAQ BD03688272 >
dmesg:
OpenBSD 4.2 (GENERIC.MP) #252: Tue Aug 28 10:53:04 MDT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 931 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 804859904 (767MB)
avail mem = 770043904 (734MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000,
SMBIOS rev. 2.3 @ 0xf206c (25 entries)
bios0: vendor Compaq version "P17" date 12/18/2002
bios0: Compaq ProLiant DL380
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 7 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks OSB4" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xe8000/0x6000
0xee000/0x2000!
acpi at mainbus0 not configured
mainbus0: Intel MP Specification (Version 1.4)
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: apic clock running at 132 MHz
cpu1 at mainbus0: apid 0 (application processor)
cpu1: Intel Pentium III ("GenuineIntel" 686-class) 931 MHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
mainbus0: bus 0 is type PCI
mainbus0: bus 3 is type PCI
mainbus0: bus 9 is type ISA
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 11, 35 pins
ioapic0: misconfigured as apic 0, remapped to apid 8
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x05
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x05
pci1 at pchb1 bus 3
ciss0 at pci1 dev 4 function 0 "Compaq Smart Array 5300 rev.2" rev 0x02:
apic 8 int 11 (irq 11)
ciss0: 1 LD, HW rev 0, FW 3.54/3.54
scsibus0 at ciss0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <COMPAQ, LOGICAL VOLUME, 3.54> SCSI0
0/direct fixed
sd0: 69455MB, 8854 cyl, 255 head, 63 sec, 512 bytes/sec, 142245120 sec total
fxp0 at pci1 dev 5 function 0 "Intel 8255x" rev 0x0d, i82550: apic 8 int
15 (irq 15), address 00:02:b3:8f:14:2c
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
siop0 at pci0 dev 1 function 0 "Symbios Logic 53c1510D" rev 0x02: apic 8
int 5 (irq 5), using 4K of on-board RAM
scsibus1 at siop0: 16 targets
siop1 at pci0 dev 1 function 1 "Symbios Logic 53c1510D" rev 0x02: apic 8
int 11 (irq 11), using 4K of on-board RAM
scsibus2 at siop1: 16 targets
st0 at scsibus2 targ 6 lun 0: <COMPAQ, SDT-10000, 1.12> SCSI2
1/sequential removable
fxp1 at pci0 dev 2 function 0 "Intel 8255x" rev 0x08, i82559: apic 8 int
10 (irq 10), address 00:02:a5:28:55:62
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
"ATI Mach64 GV" rev 0x7a at pci0 dev 3 function 0 not configured
"Compaq Netelligent ASMC" rev 0x00 at pci0 dev 4 function 0 not configured
ppb0 at pci0 dev 5 function 0 "Intel S21152BB PCI-PCI" rev 0x00
pci2 at ppb0 bus 1
vga1 at pci2 dev 0 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Compaq Netelligent ASMC" rev 0x00 at pci2 dev 1 function 0 not configured
vendor "Compaq", unknown product 0x005a (class memory subclass
miscellaneous, rev 0x00) at pci2 dev 2 function 0 not configured
vendor "Compaq", unknown product 0x00b1 (class memory subclass
miscellaneous, rev 0x01) at pci2 dev 4 function 0 not configured
piixpm0 at pci0 dev 15 function 0 "ServerWorks OSB4" rev 0x4f: SMBus
disabled
pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
atapiscsi0 at pciide0 channel 0 drive 0
scsibus3 at atapiscsi0: 2 targets
cd0 at scsibus3 targ 0 lun 0: <COMPAQ, CD-224E, 9.0B> SCSI0 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: no compatibility interrupt for use by channel 1
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a swap on sd0b dump on sd0b
