I had some similar issue on the HP DL 120 G5. Solution is: desactivate the RAID controler in the BIOS. If you need the use some raid, use raidctl which is working again in version 4.4
-----Message d'origine----- De : [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] De la part de Alexander Hall Envoyi : jeudi 6 novembre 2008 14:44 @ : misc@openbsd.org; [EMAIL PROTECTED] Objet : HP DL180 hangs on boot Hi! I have issues booting a HP ProLiant DL180 G5 ("456830-421") [1] which I hope someone can shed some light on. [ While writing thie email I've done some more testing and realized that the behaviour is not really consistent, but what I describe below is a typical case ] 1. The machine takes loong pauses (usually two; sometimes more) while loading the kernel. - The first long pause is after "entry point at ..." line, and is about 90s. [noticed now that pressing any key on the keyboard makes it go on... interrupt issues?] - Second pause is after "pckbd0 at isa0..." and lasts approximately 3 to 5 minutes. Dunno if it means anything, but somewhere in between the pauses described first above, the machine beeps once. I get similar beeps when adding or removing an usb stick, so it might be related to usb. 2. Sometimes the machine shuts down and restarts slightly after the kernel is loaded (might have time to show the "(I)nstall..." prompt). I don't have serial console for now so I cannot tell exactly. A few times I have seen the capital letter "F" being printed out (gray on blue) prior to the reboot. disabling isa and pci seems to make it not hang but makes it rather unusable... :-d If the machine gets past loading and initializing the kernel without rebooting, it seems fine but all I've done so far is installing 4.4. The HP product id is "456830-421" with 1G RAM replaced by 4G (2+2) and a 250GB SATA drive. The machine has no proper raid AFAICT (ie no E200 or P400) but some (likely crappy) built-in semi-raid. Reinserting the original memory stick did not improve anything, nor did removing the harddrive. The diagnostics test showed no errors, but i'm running it now over the weekend. I'm going to try a firmware upgrade too. Any clues are appreciated. dmesg from after the succesful install (bsd.rd) follows. Thanks, Alexander [1] http://h10010.www1.hp.com/wwpc/uk/en/sm/WF06b/15351-15351-3328412-3328421-33 28421-3580698-3673202.html ============================================== OpenBSD 4.4-current (RAMDISK_CD) #203: Sun Nov 2 13:41:35 MST 2008 [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD real mem = 3745857536 (3572MB) avail mem = 3635634176 (3467MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xfc4b0 (65 entries) bios0: vendor HP version "O19" date 08/20/2008 bios0: HP ProLiant DL180 G5 acpi0 at bios0: rev 2 acpi0: tables DSDT FACP APIC MCFG SPMI SLIC OEMB HPET SSDT EINJ BERT ERST HEST acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus 1 (NPE2) acpiprt2 at acpi0: bus 2 (NPE3) acpiprt3 at acpi0: bus 3 (NPE4) acpiprt4 at acpi0: bus 5 (NPE6) acpiprt5 at acpi0: bus 10 (P0P1) acpiprt6 at acpi0: bus 9 (P0PE) acpiprt7 at acpi0: bus 8 (P0P3) acpiprt8 at acpi0: bus 7 (BCM_) cpu0 at mainbus0: (uniprocessor) cpu0: Intel(R) Xeon(R) CPU E5420 @ 2.50GHz, 2494.12 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLU SH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX1 6,xTPR,NXE,LONG cpu0: 6MB 64b/line 16-way L2 cache pci0 at mainbus0 bus 0: configuration mode 1 pchb0 at pci0 dev 0 function 0 "Intel 5100 Host" rev 0x80 ppb0 at pci0 dev 2 function 0 "Intel 5100 PCIE" rev 0x80 pci1 at ppb0 bus 1 ppb1 at pci0 dev 3 function 0 "Intel 5100 PCIE" rev 0x80 pci2 at ppb1 bus 2 ppb2 at pci0 dev 4 function 0 "Intel 5100 PCIE" rev 0x80 pci3 at ppb2 bus 3 ppb3 at pci0 dev 5 function 0 "Intel 5100 PCIE" rev 0x80 pci4 at ppb3 bus 4 ppb4 at pci0 dev 6 function 0 "Intel 5100 PCIE" rev 0x80 pci5 at ppb4 bus 5 ppb5 at pci0 dev 7 function 0 "Intel 5100 PCIE" rev 0x80 pci6 at ppb5 bus 6 pchb1 at pci0 dev 16 function 0 "Intel 5100 FSB" rev 0x80 pchb2 at pci0 dev 16 function 1 "Intel 5100 FSB" rev 0x80 pchb3 at pci0 dev 16 function 2 "Intel 5100 FSB" rev 0x80 pchb4 at pci0 dev 17 function 0 "Intel 5100 Reserved" rev 0x80 pchb5 at pci0 dev 19 function 0 "Intel 5100 Reserved" rev 0x80 pchb6 at pci0 dev 21 function 0 "Intel 5100 DDR" rev 0x80 pchb7 at pci0 dev 22 function 0 "Intel 5100 DDR" rev 0x80 uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: irq 11 uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: irq 14 uhci2 at pci0 dev 26 function 2 "Intel 82801I USB" rev 0x02: irq 5 ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: irq 15 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb6 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: irq 11 pci7 at ppb6 bus 9 ppb7 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: irq 11 pci8 at ppb7 bus 8 vga1 at pci8 dev 0 function 0 "Matrox MGA G200e (ServerEngines)" rev 0x02 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) ppb8 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02: irq 10 pci9 at ppb8 bus 7 bge0 at pci9 dev 0 function 0 "Broadcom BCM5722" rev 0x00, BCM5755 C0 (0xa200): irq 10, address 00:22:64:42:1b:23 brgphy0 at bge0 phy 1: BCM5722 10/100/1000baseT PHY, rev. 0 uhci3 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: irq 7 uhci4 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: irq 5 uhci5 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: irq 15 ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: irq 7 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb9 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92 pci10 at ppb9 bus 10 "Intel 82801IR LPC" rev 0x02 at pci0 dev 31 function 0 not configured pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide0: using irq 5 for native-PCI interrupt wd0 at pciide0 channel 0 drive 0: <GB0250EAFJF> wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 "Intel 82801I SMBus" rev 0x02 at pci0 dev 31 function 3 not configured pciide1 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA, channel 0 wired to native-PCI, channel 1 wired to native-PCI pciide1: using irq 5 for native-PCI interrupt usb2 at uhci0: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb3 at uhci1: USB revision 1.0 uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb4 at uhci2: USB revision 1.0 uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb5 at uhci3: USB revision 1.0 uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb6 at uhci4: USB revision 1.0 uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb7 at uhci5: USB revision 1.0 uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at mainbus0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 rd0: fixed, 4480 blocks uhidev0 at uhub5 port 1 configuration 1 interface 0 "ServerEngines SE USB Device" rev 1.10/0.01 addr 2 uhidev0: iclass 3/1 ukbd0 at uhidev0 wskbd1 at ukbd0 mux 1 wskbd1: connecting to wsdisplay0 uhidev1 at uhub5 port 1 configuration 1 interface 1 "ServerEngines SE USB Device" rev 1.10/0.01 addr 2 uhidev1: iclass 3/1 uhid at uhidev1 not configured uhidev2 at uhub4 port 1 configuration 1 interface 0 "Logitech USB Receiver" rev 1.10/38.10 addr 2 uhidev2: iclass 3/1 ukbd1 at uhidev2 wskbd2 at ukbd1 mux 1 wskbd2: connecting to wsdisplay0 uhidev3 at uhub4 port 1 configuration 1 interface 1 "Logitech USB Receiver" rev 1.10/38.10 addr 2 uhidev3: iclass 3/1, 17 report ids uhid at uhidev3 reportid 2 not configured uhid at uhidev3 reportid 3 not configured uhid at uhidev3 reportid 4 not configured uhid at uhidev3 reportid 16 not configured uhid at uhidev3 reportid 17 not configured softraid0 at root PXE boot MAC address 00:22:64:42:1b:23, interface bge0 root on rd0a swap on rd0b dump on rd0b
