Hello
i'm looking for advices as i have recently a lot of errors messages
about CF in my soekris (dmesg at the end)
i reinstall my box and get the following during install
(1: Crucial Tech CF 1GB)
>>>
The next step *DESTROYS* all existing data on these partitions!
Are you really sure that you're ready to proceed? [no] yes
/dev/rwd0a: 967.6MB in 1981664 sectors of 512 bytes
5 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
wd0(pciide0:0:1): timeout
type: ata
c_bcount: 8192
c_skip: 0
pciide0:0:1: bus-master DMA error: missing interrupt, status=0x41
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn
16), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn
16), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn
16), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn
16), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn
16), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 79; cn 0 tn 1 sn 16)
newfs: wtfs: write error on block 16: Input/output error
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2), retrying
pciide0:0:1: not ready, st=0x80<BSY>, err=0x00
pciide0 channel 0: reset failed for drive 1
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3
sn 2)
mount_ffs: /dev/wd0a on /mnt: Input/output error
FATAL ERROR: Cannot mount filesystems. Double-check your configuration
and restart the install.
#
<<<
i also repeat this with
(2: Sandisk 256MB)
install goes to end with a few warnings:
>>>
The next step *DESTROYS* all existing data on these partitions!
Are you really sure that you're ready to proceed? [no] yes
/dev/rwd0a: 244.7MB in 501216 sectors of 512 bytes
5 cylinder groups of 50.05MB, 6406 blocks, 12864 inodes each
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 8192
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x21
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 48; cn 0 tn 1 sn
16), retrying
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 8192
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x21
wd0: transfer error, downgrading to PIO mode 4
wd0(pciide0:0:0): using PIO mode 4
wd0a: device timeout writing fsbn 16 of 16-31 (wd0 bn 48; cn 0 tn 1 sn
16), retrying
wd0: soft error (corrected)
/dev/wd0a on /mnt type ffs (rw, asynchronous, local, ctime=Mon Nov 24
06:36:02 2008)
System hostname? (short form, e.g. 'foo')
<<<
do you think CF are too old (too much write) ? or is there a problem
with my motherboard ?
thanks
Regards
Julien
dmesg:
OpenBSD 4.4 (RAMDISK_CD) #857: Tue Aug 12 17:31:49 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133787648 (127MB)
avail mem = 122793984 (117MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/40/21, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:58:cc
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:58:cd
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c3:58:ce
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
ral0 at pci0 dev 14 function 0 "Ralink RT2561S" rev 0x00: irq 11,
address 00:12:0e:61:7f:c0
ral0: MAC/BBP RT2561C, RF RT5225
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 1: <CF 1GB>
wd0: 1-sector PIO, LBA, 967MB, 1981728 sectors
wd0(pciide0:0:1): using PIO mode 4, DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5,
version 1.0, legacy support
isa0 at gscpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask f3e5 netmask ffe5 ttymask ffff
rd0: fixed, 3800 blocks
softraid0 at root
PXE boot MAC address 00:00:24:c3:58:cc, interface sis0
root on rd0a swap on rd0b dump on rd0b
