Hello,
I have just bought a Fabia FX5621 board which has amongst others, two
Agere ET1310 interfaces. I configured one interface and it negotiated
correctly with my switch at 1000mbps full duplex. However, I am not able
to ping the interface from anywhere else and I am not able to ping from
the interface either. The ARP table seems always empty. I used tcpdump
to sniff the traffic while pinging and doing some broadcasts and saw
nothing in the tcpdump output.
Has someone else noticed this kind of behavior with this chipset?
here is my dmesg:
OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: VIA Eden Processor 1000MHz ("CentaurHauls" 686-class) 1 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,SSE3,EST,TM2,xTPR
real mem = 1039757312 (991MB)
avail mem = 997048320 (950MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/16/09, BIOS32 rev. 0 @ 0xf0010,
SMBIOS rev. 2.5 @ 0xfc390 (47 entries)
bios0: vendor American Megatrends Inc. version "080014" date 01/16/2009
acpi at bios0 function 0x0 not configured
mpbios0 at bios0: Intel MP Specification 1.4
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: RNG AES AES-CTR SHA1 SHA256 RSA
cpu0: apic clock running at 99MHz
mpbios0: bus 0 is type PCI
mpbios0: bus 1 is type PCI
mpbios0: bus 128 is type PCI
mpbios0: bus 129 is type PCI
mpbios0: bus 130 is type PCI
mpbios0: bus 131 is type ISA
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 3, 24 pins
pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf5780/336 (19 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0x1106 product 0x3287
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #130 is the last bus
bios0: ROM list: 0xc0000/0xfe00
cpu0: unknown Enhanced SpeedStep CPU, msr 0x04090a0904000a09
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 1333 MHz (844 mV): speeds: 1333, 533 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA CN700 Host" rev 0x00
viaagp0 at pchb0: v3
agp0 at viaagp0: aperture at 0xe0000000, size 0x10000000
pchb1 at pci0 dev 0 function 1 "VIA CN700 Host" rev 0x00
pchb2 at pci0 dev 0 function 2 "VIA CN700 Host" rev 0x00
pchb3 at pci0 dev 0 function 3 "VIA PT890 Host" rev 0x00
pchb4 at pci0 dev 0 function 4 "VIA CN700 Host" rev 0x00
pchb5 at pci0 dev 0 function 7 "VIA CN700 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA S3 Unichrome PRO IGP" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ral0 at pci0 dev 8 function 0 "Ralink RT2561S" rev 0x00: apic 1 int 16
(irq 11), address 00:12:0e:61:49:24
ral0: MAC/BBP RT2561C, RF RT5225
rl0 at pci0 dev 9 function 0 "Realtek 8139" rev 0x10: apic 1 int 16 (irq
11), address 00:04:a7:08:9a:c6
rlphy0 at rl0 phy 0: RTL internal PHY
rl1 at pci0 dev 10 function 0 "Realtek 8139" rev 0x10: apic 1 int 17
(irq 10), address 00:04:a7:08:9a:c5
rlphy1 at rl1 phy 0: RTL internal PHY
rl2 at pci0 dev 11 function 0 "Realtek 8139" rev 0x10: apic 1 int 18
(irq 5), address 00:04:a7:08:9a:c4
rlphy2 at rl2 phy 0: RTL internal PHY
rl3 at pci0 dev 12 function 0 "Realtek 8139" rev 0x10: apic 1 int 19
(irq 3), address 00:04:a7:08:9a:c3
rlphy3 at rl3 phy 0: RTL internal PHY
ahci0 at pci0 dev 15 function 0 vendor "VIA", unknown product 0x6287 rev
0x20: apic 1 int 21 (irq 10), AHCI 1.0
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, ST9500325AS, 0001> SCSI3 0/direct fixed
sd0: 476940MB, 512 bytes/sec, 976773168 sec total
pciide0 at pci0 dev 15 function 1 "VIA VT82C571 IDE" rev 0x07: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 disabled (no drives)
wd0 at pciide0 channel 1 drive 0: <ELITE PRO CF CARD 16GB>
wd0: 1-sector PIO, LBA, 15391MB, 31522176 sectors
wd0(pciide0:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x91: apic 1 int
20 (irq 11)
ehci0 at pci0 dev 16 function 4 "VIA VT6202 USB" rev 0x90: apic 1 int 22
(irq 5)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1
viapm0 at pci0 dev 17 function 0 "VIA VT8251 ISA" rev 0x00
iic0 at viapm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
pchb6 at pci0 dev 17 function 7 "VIA VT8251 VLINK" rev 0x00
ppb1 at pci0 dev 19 function 0 "VIA VT8251 PCIE" rev 0x00
pci2 at ppb1 bus 128
ppb2 at pci2 dev 0 function 0 "VIA VT8251 PCIE" rev 0x00
pci3 at ppb2 bus 130
et0 at pci3 dev 0 function 0 "AT&T/Lucent ET1310" rev 0x01: apic 1 int
17 (irq 11), address 00:04:a7:04:e6:a4
etphy0 at et0 phy 0: ET1011 10/100/1000baseT PHY, rev. 2
ppb3 at pci2 dev 0 function 1 "VIA VT8251 PCIE" rev 0x00
pci4 at ppb3 bus 129
et1 at pci4 dev 0 function 0 "AT&T/Lucent ET1310" rev 0x03: apic 1 int
16 (irq 11), address 00:04:a7:04:e5:5e
etphy1 at et1 phy 0: ET1011 10/100/1000baseT PHY, rev. 2
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8712F rev 8, EC port 0xa10
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
--
010100100110010101101110011000010111010101100100
010000010110110001101100011000010111001001100100
