On Sat, Nov 28, 2009 at 1:35 AM, Peter Miller <feu...@gmail.com> wrote: > I have 4.6 amd64 installed and can't get X to work at 1280x800. > > After a default install X won't start and i get an error which i think > is caused by nv. I created a xorg.conf file using "X -configure" and > then changed the driver from "nv" to "vesa' and was able to get X > running, but only at 800x600 resolution. xrandr showed 800x600 as the > max supported resolution. > > Then I added the following to the Monitor section of xorg.conf and was > able to get 1024x768. > > HorizSync 30-120 > VertRefresh 50-150 (i have no reason for these numbers.. they just worked) > > I have tried adding a modeline to solve the problem, but without luck. > I'm not quite sure how to get a proper modeline. I used this site to > get mine. > http://www.arachnoid.com/modelines/ > resulting modeline > > # 1280x800 @ 60.00 Hz (GTF) hsync: 49.68 kHz; pclk: 83.46 MHz > Modeline "1280x800_60.00" 83.46 1280 1344 1480 1680 800 801 804 828 > -HSync +Vsync > > So here's some output > The original Xorg.0.log error after install. Can't get into X. > > (--) checkDevMem: using aperture driver /dev/xf86 > (--) Using wscons driver on /dev/ttyC4 in pcvt compatibility mode (version 3.32) > > X.Org X Server 1.5.3 > Release Date: 5 November 2008 > X Protocol Version 11, Revision 0 > Build Operating System: OpenBSD 4.6 amd64 > Current Operating System: OpenBSD wobsd.funny.org 4.6 MYKERN.MP#0 amd64 > Build Date: 01 July 2009 05:32:34PM > > Before reporting problems, check http://wiki.x.org > to make sure that you have the latest version. > Markers: (--) probed, (**) from config file, (==) default setting, > (++) from command line, (!!) notice, (II) informational, > (WW) warning, (EE) error, (NI) not implemented, (??) unknown. > (==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov 27 18:59:14 2009 > (EE) Unable to locate/open config file > (II) Loader magic: 0x771560 > (II) Module ABI versions: > X.Org ANSI C Emulation: 0.4 > X.Org Video Driver: 4.1 > X.Org XInput driver : 2.1 > X.Org Server Extension : 1.1 > X.Org Font Renderer : 0.6 > (II) Loader running on openbsd > (--) PCI: (0...@0:1:3) NVIDIA MCP67 Co-processor rev 162, Mem @ 0xfc200000/524288 > (--) PCI:*(0...@0:18:0) NVIDIA unknown chipset (0x0531) rev 162, Mem @ > 0xf4000000/16777216, 0xd0000000/268435456, 0xf0000000/16777216 > (==) Matched nv for the autoconfigured driver > New driver is "nv" > (==) Using default built-in configuration (30 lines) > (==) --- Start of built-in configuration --- > Section "Device" > Identifier "Builtin Default nv Device 0" > Driver "nv" > EndSection > Section "Screen" > Identifier "Builtin Default nv Screen 0" > Device "Builtin Default nv Device 0" > EndSection > Section "Device" > Identifier "Builtin Default fbdev Device 0" > Driver "fbdev" > EndSection > Section "Screen" > Identifier "Builtin Default fbdev Screen 0" > Device "Builtin Default fbdev Device 0" > EndSection > Section "Device" > Identifier "Builtin Default vesa Device 0" > Driver "vesa" > EndSection > Section "Screen" > Identifier "Builtin Default vesa Screen 0" > Device "Builtin Default vesa Device 0" > EndSection > Section "ServerLayout" > Identifier "Builtin Default Layout" > Screen "Builtin Default nv Screen 0" > Screen "Builtin Default fbdev Screen 0" > Screen "Builtin Default vesa Screen 0" > EndSection > (==) --- End of built-in configuration --- > (==) ServerLayout "Builtin Default Layout" > (**) |-->Screen "Builtin Default nv Screen 0" (0) > (**) | |-->Monitor "<default monitor>" > (**) | |-->Device "Builtin Default nv Device 0" > (==) No monitor specified for screen "Builtin Default nv Screen 0". > Using a default monitor configuration. > (**) |-->Screen "Builtin Default fbdev Screen 0" (1) > (**) | |-->Monitor "<default monitor>" > (**) | |-->Device "Builtin Default fbdev Device 0" > (==) No monitor specified for screen "Builtin Default fbdev Screen 0". > Using a default monitor configuration. > (**) |-->Screen "Builtin Default vesa Screen 0" (2) > (**) | |-->Monitor "<default monitor>" > (**) | |-->Device "Builtin Default vesa Device 0" > (==) No monitor specified for screen "Builtin Default vesa Screen 0". > Using a default monitor configuration. > (==) Not automatically adding devices > (==) Not automatically enabling devices > (==) No FontPath specified. Using compiled-in default. > (==) FontPath set to: > /usr/X11R6/lib/X11/fonts/misc/, > /usr/X11R6/lib/X11/fonts/TTF/, > /usr/X11R6/lib/X11/fonts/OTF, > /usr/X11R6/lib/X11/fonts/Type1/, > /usr/X11R6/lib/X11/fonts/100dpi/, > /usr/X11R6/lib/X11/fonts/75dpi/ > (==) ModulePath set to "/usr/X11R6/lib/modules" > (==) |-->Input Device "<default pointer>" > (==) |-->Input Device "<default keyboard>" > (==) The core pointer device wasn't specified explicitly in the layout. > Using the default mouse configuration. > (==) The core keyboard device wasn't specified explicitly in the layout. > Using the default keyboard configuration. > (II) System resource ranges: > [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) > [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] > [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] > [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] > [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] > [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] > (II) LoadModule: "extmod" > > (II) Loading /usr/X11R6/lib/modules/extensions//libextmod.so > (II) Module extmod: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.0.0 > Module class: X.Org Server Extension > ABI class: X.Org Server Extension, version 1.1 > (II) Loading extension SHAPE > (II) Loading extension MIT-SUNDRY-NONSTANDARD > (II) Loading extension BIG-REQUESTS > (II) Loading extension SYNC > (II) Loading extension MIT-SCREEN-SAVER > (II) Loading extension XC-MISC > (II) Loading extension XFree86-VidModeExtension > (II) Loading extension XFree86-Misc > (II) Loading extension XFree86-DGA > (II) Loading extension DPMS > (II) Loading extension TOG-CUP > (II) Loading extension Extended-Visual-Information > (II) Loading extension XVideo > (II) Loading extension XVideo-MotionCompensation > (II) Loading extension X-Resource > (II) LoadModule: "dbe" > > (II) Loading /usr/X11R6/lib/modules/extensions//libdbe.so > (II) Module dbe: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.0.0 > Module class: X.Org Server Extension > ABI class: X.Org Server Extension, version 1.1 > (II) Loading extension DOUBLE-BUFFER > (II) LoadModule: "glx" > > (II) Loading /usr/X11R6/lib/modules/extensions//libglx.so > (II) Module glx: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.0.0 > ABI class: X.Org Server Extension, version 1.1 > (==) AIGLX enabled > (==) Exporting typical set of GLX visuals > (II) Loading extension GLX > (II) LoadModule: "freetype" > > (II) Loading /usr/X11R6/lib/modules/fonts//libfreetype.so > (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" > compiled for 1.5.3, module version = 2.1.0 > Module class: X.Org Font Renderer > ABI class: X.Org Font Renderer, version 0.6 > (II) Loading font FreeType > (II) LoadModule: "dri" > > (II) Loading /usr/X11R6/lib/modules/extensions//libdri.so > (II) Module dri: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.0.0 > ABI class: X.Org Server Extension, version 1.1 > (II) Loading extension XFree86-DRI > (II) LoadModule: "nv" > > (II) Loading /usr/X11R6/lib/modules/drivers//nv_drv.so > (II) Module nv: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 2.1.13 > Module class: X.Org Video Driver > ABI class: X.Org Video Driver, version 4.1 > (II) LoadModule: "fbdev" > > (WW) Warning, couldn't open module fbdev > (II) UnloadModule: "fbdev" > (EE) Failed to load module "fbdev" (module does not exist, 0) > (II) LoadModule: "vesa" > > (II) Loading /usr/X11R6/lib/modules/drivers//vesa_drv.so > (II) Module vesa: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 2.2.0 > Module class: X.Org Video Driver > ABI class: X.Org Video Driver, version 4.1 > (II) LoadModule: "mouse" > > (II) Loading /usr/X11R6/lib/modules/input//mouse_drv.so > (II) Module mouse: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.4.0 > Module class: X.Org XInput Driver > ABI class: X.Org XInput driver, version 2.1 > (II) LoadModule: "kbd" > > (II) Loading /usr/X11R6/lib/modules/input//kbd_drv.so > (II) Module kbd: vendor="X.Org Foundation" > compiled for 1.5.3, module version = 1.3.2 > Module class: X.Org XInput Driver > ABI class: X.Org XInput driver, version 2.1 > (II) NV: driver for NVIDIA chipsets: RIVA 128, RIVA TNT, RIVA TNT2, > Unknown TNT2, Vanta, RIVA TNT2 Ultra, RIVA TNT2 Model 64, > Aladdin TNT2, GeForce 256, GeForce DDR, Quadro, GeForce2 MX/MX 400, > GeForce2 MX 100/200, GeForce2 Go, Quadro2 MXR/EX/Go, > GeForce2 Integrated GPU, GeForce2 GTS, GeForce2 Ti, GeForce2 Ultra, > Quadro2 Pro, GeForce4 MX 460, GeForce4 MX 440, GeForce4 MX 420, > GeForce4 MX 440-SE, GeForce4 440 Go, GeForce4 420 Go, > GeForce4 420 Go 32M, GeForce4 460 Go, Quadro4 550 XGL, > GeForce4 440 Go 64M, Quadro NVS, Quadro4 500 GoGL, > GeForce4 410 Go 16M, GeForce4 MX 440 with AGP8X, > GeForce4 MX 440SE with AGP8X, GeForce4 MX 420 with AGP8X, > GeForce4 MX 4000, GeForce4 448 Go, GeForce4 488 Go, Quadro4 580 XGL, > Quadro4 NVS 280 SD, Quadro4 380 XGL, Quadro NVS 50 PCI, > GeForce4 448 Go, GeForce4 MX Integrated GPU, GeForce3, > GeForce3 Ti 200, GeForce3 Ti 500, Quadro DCC, GeForce4 Ti 4600, > GeForce4 Ti 4400, GeForce4 Ti 4200, Quadro4 900 XGL, Quadro4 750 XGL, > Quadro4 700 XGL, GeForce4 Ti 4800, GeForce4 Ti 4200 with AGP8X, > GeForce4 Ti 4800 SE, GeForce4 4200 Go, Quadro4 700 GoGL, > Quadro4 980 XGL, Quadro4 780 XGL, GeForce FX 5800 Ultra, > GeForce FX 5800, Quadro FX 2000, Quadro FX 1000, > GeForce FX 5600 Ultra, GeForce FX 5600, GeForce FX 5600XT, > GeForce FX Go5600, GeForce FX Go5650, Quadro FX Go700, > GeForce FX 5200, GeForce FX 5200 Ultra, GeForce FX 5200, > GeForce FX 5200LE, GeForce FX Go5200, GeForce FX Go5250, > GeForce FX 5500, GeForce FX 5100, GeForce FX Go5200 32M/64M, > Quadro NVS 55/280 PCI, Quadro FX 500/600 PCI, > GeForce FX Go53xx Series, GeForce FX Go5100, GeForce FX 5900 Ultra, > GeForce FX 5900, GeForce FX 5900XT, GeForce FX 5950 Ultra, > GeForce FX 5900ZT, Quadro FX 3000, Quadro FX 700, > GeForce FX 5700 Ultra, GeForce FX 5700, GeForce FX 5700LE, > GeForce FX 5700VE, GeForce FX Go5700, GeForce FX Go5700, > Quadro FX Go1000, Quadro FX 1100, GeForce 6800 Ultra, GeForce 6800, > GeForce 6800 LE, GeForce 6800 XE, GeForce 6800 XT, GeForce 6800 GT, > GeForce 6800 GT, GeForce 6800 GS, GeForce 6800 XT, Quadro FX 4000, > GeForce 6800 GS, GeForce 6800, GeForce 6800 LE, GeForce 6800 XT, > GeForce Go 6800, GeForce Go 6800 Ultra, Quadro FX Go1400, > Quadro FX 3450/4000 SDI, Quadro FX 1400, GeForce 6600 GT, > GeForce 6600, GeForce 6600 LE, GeForce 6600 VE, GeForce Go 6600, > GeForce 6610 XL, GeForce Go 6600 TE/6200 TE, GeForce 6700 XL, > GeForce Go 6600, GeForce Go 6600 GT, Quadro FX 550, Quadro FX 550, > Quadro FX 540, GeForce 6200, GeForce 6500, > GeForce 6200 TurboCache(TM), GeForce 6200SE TurboCache(TM), > GeForce 6200 LE, GeForce Go 6200, Quadro NVS 285, GeForce Go 6400, > GeForce Go 6200, GeForce Go 6400, GeForce 6250, GeForce 7100 GS, > GeForce 6800, GeForce 6800 LE, GeForce 6800 GT, GeForce 6800 XT, > GeForce 6200, GeForce 6200 A-LE, GeForce 7800 GTX, GeForce 7800 GTX, > GeForce 7800 GT, GeForce 7800 GS, GeForce 7800 SLI, GeForce Go 7800, > GeForce Go 7800 GTX, Quadro FX 4500, GeForce 7300 LE, > GeForce 7300 SE, GeForce Go 7200, GeForce Go 7300, GeForce Go 7400, > GeForce Go 7400 GS, Quadro NVS 110M, Quadro NVS 120M, Quadro FX 350M, > GeForce 7500 LE, Quadro FX 350, GeForce 7300 GS, GeForce 7600 GT, > GeForce 7600 GS, GeForce 7300 GT, GeForce 7600 LE, GeForce 7300 GT, > GeForce Go 7700, GeForce Go 7600, GeForce Go 7600 GT, > Quadro NVS 300M, GeForce Go 7900 SE, Quadro FX 550M, Quadro FX 560, > GeForce 7900 GTX, GeForce 7900 GT, GeForce 7900 GS, > GeForce Go 7900 GS, GeForce Go 7900 GTX, Quadro FX 2500M, > Quadro FX 1500M, Quadro FX 5500, Quadro FX 3500, Quadro FX 1500, > Quadro FX 4500 X2, GeForce 6150, GeForce 6150 LE, GeForce 6100, > GeForce Go 6150, GeForce Go 6100, GeForce 8800 GTX, GeForce 8800 GTS, > GeForce 8800 Ultra, Quadro FX 5600, Quadro FX 4600, GeForce 8600 GTS, > GeForce 8600 GT, GeForce 8600 GT, GeForce 8600 GS, GeForce 8400 GS, > GeForce 9500M GS, GeForce 8600M GT, GeForce 9650M GS, > GeForce 8700M GT, Quadro FX 370, Quadro NVS 320M, Quadro FX 570M, > Quadro FX 1600M, Quadro FX 570, Quadro FX 1700, GeForce 8400 SE, > GeForce 8500 GT, GeForce 8400 GS, GeForce 8300 GS, GeForce 8400 GS, > GeForce 8600M GS, GeForce 8400M GT, GeForce 8400M GS, > GeForce 8400M G, Quadro NVS 140M, Quadro NVS 130M, Quadro NVS 135M, > GeForce 9400 GT, Quadro FX 360M, GeForce 9300M G, Quadro NVS 290, > GeForce GTX 280, GeForce GTX 260, GeForce 8800 GTS 512, > GeForce 8800 GT, GeForce 9800 GX2, GeForce 8800 GS, > GeForce 8800M GTS, GeForce 8800M GTX, GeForce 8800 GS, > GeForce 9600 GSO, GeForce 8800 GT, GeForce 9800 GTX, > GeForce 9800 GTK+, GeForce 9800 GT, Quadro FX 3700, Quadro FX 3600M, > GeForce 9600 GT, GeForce 9600 GS, GeForce 9800M GTS, > GeForce 9700M GTS, GeForce 9800M GTS, GeForce 9500 GT, > GeForce 9600M GT, GeForce 9600M GS, GeForce 9600M GT, > GeForce 9500M G, GeForce 9300 GE, GeForce 9300 GS, GeForce 8400 GS, > GeForce 9300M GS, GeForce 9200M GS, GeForce 9300M GS, > Quadro NVS 150M, Quadro NVS 160M, GeForce 9300 GE > (II) VESA: driver for VESA chipsets: vesa > (II) Primary Device is: PCI 0...@00:12:0 > (WW) NV: Ignoring unsupported device 0x10de0531 at 0...@00:12:0 > (WW) Falling back to old probe method for vesa > (EE) No devices detected. > > Fatal server error: > no screens found > > > > dmesg.boot > this is a custom kernel, but the only thing i changed was adding ntfs support. > > OpenBSD 4.6 (MYKERN.MP) #0: Fri Nov 27 13:15:55 UTC 2009 > p...@wobsd.funny.org:/usr/src/sys/arch/amd64/compile/MYKERN.MP > real mem = 3152347136 (3006MB) > avail mem = 3044294656 (2903MB) > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xdc010 (27 entries) > bios0: vendor Hewlett-Packard version "F.21" date 02/28/2008 > bios0: Hewlett-Packard HP Pavilion dv2700 Notebook PC > acpi0 at bios0: rev 3 > acpi0: tables DSDT FACP SLIC WDAT SRAT MCFG HPET APIC BOOT SSDT > acpi0: wakeup devices LID0(S3) SLPB(S3) MAC0(S5) P2P0(S5) MCEB(S4) > DVDB(S4) QPWB(S4) PICB(S4) VDOB(S4) LTVB(S4) MUSB(S4) KBD0(S3) > PS2M(S3) > acpitimer0 at acpi0: 3579545 Hz, 24 bits > acpihpet0 at acpi0: 25000000 Hz > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: AMD Turion(tm) 64 X2 TL-60, 2000.46 MHz > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > 64b/line 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: apic clock running at 200MHz > cpu1 at mainbus0: apid 1 (application processor) > cpu1: AMD Turion(tm) 64 X2 TL-60, 2000.19 MHz > cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > 64b/line 16-way L2 cache > cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 11, 24 pins > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 1 (P2P0) > acpiprt2 at acpi0: bus 255 (XVR0) > acpiprt3 at acpi0: bus 6 (XVR1) > acpiprt4 at acpi0: bus 4 (XVR2) > acpiec0 at acpi0 > acpicpu0 at acpi0: PSS > acpicpu1 at acpi0: PSS > acpitz0 at acpi0: critical temperature 120 degC > acpitz1 at acpi0: critical temperature 120 degC > acpibtn0 at acpi0: LID0 > acpibtn1 at acpi0: SLPB > acpibtn2 at acpi0: PWRB > acpibat0 at acpi0: BAT0 model "Primary" type LION oem "Hewlett-Packard " > acpiac0 at acpi0: AC unit offline > acpivideo0 at acpi0: VGA_ > acpivout0 at acpivideo0: CRT_ > acpivout1 at acpivideo0: LCD_ > acpivout2 at acpivideo0: TVO_ > cpu0: PowerNow! K8 2000 MHz: speeds: 2000 1800 1600 800 MHz > pci0 at mainbus0 bus 0 > "NVIDIA MCP67 Memory" rev 0xa2 at pci0 dev 0 function 0 not configured > pcib0 at pci0 dev 1 function 0 "NVIDIA MCP67 ISA" rev 0xa2 > nviic0 at pci0 dev 1 function 1 "NVIDIA MCP67 SMBus" rev 0xa2 > iic0 at nviic0 > iic1 at nviic0 > spdmem0 at iic1 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > spdmem1 at iic1 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > "NVIDIA MCP67 Memory" rev 0xa2 at pci0 dev 1 function 2 not configured > "NVIDIA MCP67 Co-processor" rev 0xa2 at pci0 dev 1 function 3 not configured > ohci0 at pci0 dev 2 function 0 "NVIDIA MCP67 USB" rev 0xa2: apic 2 int > 11 (irq 11), version 1.0, legacy support > ehci0 at pci0 dev 2 function 1 "NVIDIA MCP67 USB" rev 0xa2: apic 2 int 7 (irq 7) > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "NVIDIA EHCI root hub" rev 2.00/1.00 addr 1 > ohci1 at pci0 dev 4 function 0 "NVIDIA MCP67 USB" rev 0xa2: apic 2 int > 10 (irq 10), version 1.0, legacy support > ehci1 at pci0 dev 4 function 1 "NVIDIA MCP67 USB" rev 0xa2: apic 2 int > 11 (irq 11) > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 "NVIDIA EHCI root hub" rev 2.00/1.00 addr 1 > pciide0 at pci0 dev 6 function 0 "NVIDIA MCP67 IDE" rev 0xa1: DMA, > channel 0 configured to compatibility, channel 1 configured to > compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <Slimtype, DVD A DS8A1H, WH66> ATAPI > 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 > pciide0: channel 1 ignored (disabled) > azalia0 at pci0 dev 7 function 0 "NVIDIA MCP67 HD Audio" rev 0xa1: > apic 2 int 10 (irq 10) > azalia0: codecs: Conexant CX20561 > audio0 at azalia0 > ppb0 at pci0 dev 8 function 0 "NVIDIA MCP67 PCI" rev 0xa2 > pci1 at ppb0 bus 1 > "Ricoh 5C832 Firewire" rev 0x05 at pci1 dev 9 function 0 not configured > sdhc0 at pci1 dev 9 function 1 "Ricoh 5C822 SD/MMC" rev 0x22: apic 2 > int 10 (irq 11) > sdmmc0 at sdhc0 > "Ricoh 5C843 MMC" rev 0x12 at pci1 dev 9 function 2 not configured > "Ricoh 5C592 Memory Stick" rev 0x12 at pci1 dev 9 function 3 not configured > "Ricoh 5C852 xD" rev 0x12 at pci1 dev 9 function 4 not configured > pciide1 at pci0 dev 9 function 0 "NVIDIA MCP67 SATA" rev 0xa2: DMA > pciide1: using apic 2 int 5 (irq 5) for native-PCI interrupt > wd0 at pciide1 channel 0 drive 0: <SAMSUNG HM160HI> > wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors > wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5 > nfe0 at pci0 dev 10 function 0 "NVIDIA MCP67 LAN" rev 0xa2: apic 2 int > 11 (irq 11), address 00:1d:72:52:36:01 > eephy0 at nfe0 phy 1: 88E1118 Gigabit PHY, rev. 0 > ppb1 at pci0 dev 12 function 0 "NVIDIA MCP67 PCIE" rev 0xa2 > pci2 at ppb1 bus 6 > ppb2 at pci0 dev 13 function 0 "NVIDIA MCP67 PCIE" rev 0xa2 > pci3 at ppb2 bus 4 > "Broadcom BCM4315" rev 0x01 at pci3 dev 0 function 0 not configured > vga1 at pci0 dev 18 function 0 vendor "NVIDIA", unknown product 0x0531 rev 0xa2 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pchb0 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00 > pchb1 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00 > pchb2 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00 > kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: > core rev BH-G2 > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > usb2 at ohci0: USB revision 1.0 > uhub2 at usb2 "NVIDIA OHCI root hub" rev 1.00/1.00 addr 1 > usb3 at ohci1: USB revision 1.0 > uhub3 at usb3 "NVIDIA OHCI root hub" rev 1.00/1.00 addr 1 > mtrr: Pentium Pro MTRR support > uvideo0 at uhub0 port 4 configuration 1 interface 0 "Chicony > Electronics Co., Ltd. HP Webcam" rev 2.00/6.04 addr 2 > video0 at uvideo0 > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > > > current xorg.conf that gets me 1024x768 > > Section "ServerLayout" > Identifier "X.org Configured" > Screen "Screen0" 0 0 > InputDevice "Mouse0" "CorePointer" > InputDevice "Keyboard0" "CoreKeyboard" > EndSection > > Section "Files" > ModulePath "/usr/X11R6/lib/modules" > FontPath "/usr/X11R6/lib/X11/fonts/misc/" > FontPath "/usr/X11R6/lib/X11/fonts/TTF/" > FontPath "/usr/X11R6/lib/X11/fonts/OTF" > FontPath "/usr/X11R6/lib/X11/fonts/Type1/" > FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" > FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" > EndSection > > Section "Module" > Load "dbe" > Load "dri" > Load "extmod" > Load "glx" > Load "freetype" > EndSection > > Section "InputDevice" > Identifier "Keyboard0" > Driver "kbd" > EndSection > > Section "InputDevice" > Identifier "Mouse0" > Driver "mouse" > Option "Protocol" "wsmouse" > Option "Device" "/dev/wsmouse" > Option "ZAxisMapping" "4 5 6 7" > EndSection > > Section "Monitor" > Identifier "Monitor0" > VendorName "Monitor Vendor" > ModelName "Monitor Model" > HorizSync 30-120 > VertRefresh 50-150 > # 1280x800 @ 60.00 Hz (GTF) hsync: 49.68 kHz; pclk: 83.46 MHz > Modeline "1280x800_60.00" 83.46 1280 1344 1480 1680 800 801 > 804 828 -HSync +Vsync > EndSection > > Section "Device" > ### Available Driver options are:- > ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", > ### <string>: "String", <freq>: "<f> Hz/kHz/MHz" > ### [arg]: arg optional > #Option "SWcursor" # [<bool>] > #Option "HWcursor" # [<bool>] > #Option "NoAccel" # [<bool>] > #Option "ShadowFB" # [<bool>] > #Option "UseFBDev" # [<bool>] > #Option "Rotate" # [<str>] > #Option "VideoKey" # <i> > #Option "FlatPanel" # [<bool>] > #Option "FPDither" # [<bool>] > #Option "CrtcNumber" # <i> > #Option "FPScale" # [<bool>] > #Option "FPTweak" # <i> > #Option "DualHead" # [<bool>] > Identifier "Card0" > Driver "vesa" > VendorName "NVIDIA" > BoardName "Unknown Board" > BusID "PCI:0:18:0" > EndSection > > Section "Screen" > Identifier "Screen0" > Device "Card0" > Monitor "Monitor0" > DefaultDepth 24 > SubSection "Display" > Viewport 0 0 > Depth 1 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 4 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 8 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 15 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 16 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 24 > Modes "1280x800" > EndSubSection > EndSection > > > xrandr output using above xorg.conf > > Screen 0: minimum 320 x 200, current 1024 x 768, maximum 1024 x 768 > default connected 1024x768+0+0 0mm x 0mm > 1024x768 85.0* > 800x600 86.0 > 640x480 86.0 > 640x400 86.0 > 320x400 0.0 > 320x240 0.0 > 320x200 0.0 > > I'm sure it'll all work if i can get the right modeline or figure out > how to get nv to work. > > Thanks > Later > Peter > >
Your nVidia card is not supported by the nv driver, so right you need to use the vesa driver. As I explained here several times, you cannot use custom mode lines with the vesa driver. You have to use one of the video modes provided by the BIOS of your card. So look at Xorg.0.log when using the vesa driver and see if there's a 1280x800 mode listed. If not (which is probably the case) you're screwed. Stay away from nVidia graphics cards, especially on laptops if you want to run an open source system on it. -- Matthieu Herrb
