You had a hardware error so the rebuild was halted. This needs some prettying up but it comes down to a bad disk. The source disk has a read error so I suggest you saving everything off the disk before proceeding.
I will write a patch to terminate the rebuild and make bioctl reflect that better. Thanks for the report. On Tue, Apr 06, 2010 at 07:47:46AM +0200, Michael Lechtermann wrote: > Hi, > > I guess this says it all: > > # bioctl -v softraid0 > Volume Status Size Device > softraid0 0 Rebuild 73543122944 sd3 RAID1 99% done > 0 Rebuild 73543122944 0:0.0 noencl <sd1a> > 'unknown serial' > 1 Online 73543122944 0:1.0 noencl <sd2a> > 'unknown serial' > > > It is at 99% since >= 8 hours. Should I replace the disk (is that > possible during a failed rebuild?) or is it some bug with softraid/bioctl? > > > > OpenBSD 4.7 (GENERIC.MP) #287: Wed Mar 17 23:57:12 MDT 2010 > [email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC.MP > real mem = 8589934592 (8192MB) > avail mem = 8385232896 (7996MB) > mainbus0 at root: Sun Fire V440 > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1062 MHz > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1062 MHz > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > cpu2 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1062 MHz > cpu2: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > cpu3 at mainbus0: SUNW,UltraSPARC-IIIi (rev 2.4) @ 1062 MHz > cpu3: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K > external (64 b/l) > "memory-controller" at mainbus0 not configured > "memory-controller" at mainbus0 not configured > "memory-controller" at mainbus0 not configured > "memory-controller" at mainbus0 not configured > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0 > schizo0: dvma map c0000000-dfffffff > pci0 at schizo0 > cas0 at pci0 dev 2 function 0 "Sun Cassini" rev 0x20: ivec 0x718, > address 00:03:ba:66:75:d1 > brgphy0 at cas0 phy 1: BCM5421 10/100/1000baseT PHY, rev. 1 > "ppm" at mainbus0 not configured > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0 > schizo1: dvma map c0000000-dfffffff > pci1 at schizo1 > mpi0 at pci1 dev 2 function 0 "Symbios Logic 53c1030" rev 0x08: ivec 0x740 > scsibus0 at mpi0: 16 targets, initiator 7 > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 0 > schizo2: dvma map c0000000-dfffffff > pci2 at schizo2 > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00 > "flashprom" at ebus0 addr 0-fffff, 290-290 not configured > rtc0 at ebus0 addr 70-71: m5819p > pcfiic0 at ebus0 addr 320-321 ivec 0x1b > iic at pcfiic0 not configured > power0 at ebus0 addr 800-82f ivec 0x1a > com0 at ebus0 addr 3f8-3ff ivec 0x22: ns16550a, 16 byte fifo > com0: console > com1 at ebus0 addr 2e8-2ef ivec 0x22: ns16550a, 16 byte fifo > "rmc-comm" at ebus0 addr 3e8-3ef ivec 0x22 not configured > cas1 at pci2 dev 2 function 0 "NS Saturn" rev 0x30: ivec 0x78c, address > 00:14:4f:1e:d6:b4 > gentbi0 at cas1 phy 0: Generic ten-bit interface, rev. 0 > machfb0 at pci2 dev 4 function 0 "ATI Rage XL" rev 0x27 > machfb0: SUNW,370-4362, 1152x900 > wsdisplay0 at machfb0 mux 1 > wsdisplay0: screen 0 added (std, sun emulation) > alipm0 at pci2 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz > clock > iic at alipm0 not configured > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec > 0x7a1, version 1.0, legacy support > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec > 0x7a5, version 1.0, legacy support > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4: > DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI > pciide0: using ivec 0x7a6 for native-PCI interrupt > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus1 at atapiscsi0: 2 targets > cd0 at scsibus1 targ 0 lun 0: <TOSHIBA, DVD-ROM SD-C2612, 1011> ATAPI > 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 disabled (no drives) > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1 > usb1 at ohci1: USB revision 1.0 > uhub1 at usb1 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1 > "ppm" at mainbus0 not configured > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0 > schizo3: dvma map c0000000-dfffffff > pci3 at schizo3 > cas2 at pci3 dev 1 function 0 "Sun Cassini" rev 0x20: ivec 0x7dc, > address 00:03:ba:66:75:d2 > brgphy1 at cas2 phy 1: BCM5421 10/100/1000baseT PHY, rev. 1 > mpi1 at pci3 dev 2 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x7e3 > scsibus2 at mpi1: 16 targets, initiator 7 > sd0 at scsibus2 targ 0 lun 0: <LSILOGIC, 1030 IM IM, 1000> SCSI2 > 0/direct fixed > sd0: 34732MB, 512 bytes/sec, 71131136 sec total > sd1 at scsibus2 targ 2 lun 0: <ModusLnk, MXJ3073SC800600X, 5704> SCSI3 > 0/direct fixed > sd1: 70136MB, 512 bytes/sec, 143638992 sec total > sd2 at scsibus2 targ 3 lun 0: <ModusLnk, MXJ3073SC800600X, 5704> SCSI3 > 0/direct fixed > sd2: 70136MB, 512 bytes/sec, 143638992 sec total > mpi1: target 2 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 > mpi1: target 3 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 > mpi1: phys disk 1 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 > mpi1: phys disk 0 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 > mpi2 at pci3 dev 2 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0x7e4 > scsibus3 at mpi2: 16 targets, initiator 7 > "i2c" at mainbus0 not configured > vscsi0 at root > scsibus4 at vscsi0: 256 targets > softraid0 at root > scsibus5 at softraid0: 1 targets > sd3 at scsibus5 targ 0 lun 0: <OPENBSD, SR RAID 1, 003> SCSI2 0/direct fixed > sd3: 70136MB, 512 bytes/sec, 143638913 sec total > bootpath: /p...@1f,700000/s...@2,0/d...@0,0 > root on sd0a swap on sd0b dump on sd0b > sd1(mpi1:2:0): Check Condition (error 0x70) on opcode 0x28 > SENSE KEY: Media Error > INFO: 0x274a (VALID flag on) > ASC/ASCQ: Read Retries Exhausted > SKSV: Actual Retry Count: 63 > softraid0: retrying read on block 9968 > softraid0: rebuild of sd3 started on sd1a > softraid0: sr_raid1_rw: illegal block count for sd3 > softraid0: could not create read io
