Hi, Let me know if I should be posting this elsewhere.
I'm running OpenBSD 4.5 i386 on an IBM x336 server, as newer versions don't work with the Broadcom network interfaces [1]. I installed it about a week ago, and everything was working great until I got the following on the console (retyped). I ran a trace as per the FAQ: [lots of vlan: lines; probably me adding the interfaces a few days ago] vlan80: initialized with non-standard mtu 1496 (parent trunk0) vlan85: initialized with non-standard mtu 1496 (parent trunk0) vlan61: initialized with non-standard mtu 1496 (parent trunk0) vlan1: initialized with non-standard mtu 1496 (parent trunk0) uvm_fault(0xd080d9e0, 0x0, 0, 1) -> e kernel: page fault trap, code=0 Stopped at arp_rtrequest+0xfb: movb 0x64(%eax),%al ddb> pckbc_start: command error ddb> trace arp_rtrequest(b,d8382048,de164df0,0) at arp_rtrequest+0xfb rtrequest1(b,de164df0,38,de164dec,0,d2ac0400,d0202de9,60) at rtrequest1+0x1f2 rtalloc1(d081a508,1,0,d839a68c) at rtalloc1+0xb6 rtalloc_mpath(d081a504,d869881c,0,d839a68c,0) at rtalloc_mpath+0x2f ip_forward(d861fa00,0,de164f10,0,204) at ip_forward+0xd8 ipv4_input(d861fa00,d2a73640,d08c2b54,d8a312b8) at ipv4_input+0x26e ipintr(d0350058,d08c0010,d06f0010,de160010,d8a312b8) at ipintr+0x64 Bad frame pointer: 0xde164f28 ddb> dmesg output is below [2]. Is this a known problem that's fixed in 4.7? Cheers, Patrick 1. http://kerneltrap.org/mailarchive/openbsd-misc/2010/3/12/6350403/thread 2. patr...@ceti-a:~[0]$ dmesg OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009 [email protected]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel(R) Xeon(TM) CPU 3.20GHz ("GenuineIntel" 686-class) 3.21 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,CNXT-ID,CX16,xTPR real mem = 2146832384 (2047MB) avail mem = 2067619840 (1971MB) mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 07/19/05, BIOS32 rev. 0 @ 0xfd711, SMBIOS rev. 2.3 @ 0xf5faa (50 entries) bios0: vendor IBM version "-[APE128AUS-1.11]-" date 07/19/2005 bios0: IBM eserver xSeries 336 -[883725M]- acpi0 at bios0: rev 2 acpi0: tables DSDT FACP APIC MCFG acpi0: wakeup devices PCI0(S5) acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: apic clock running at 200MHz cpu at mainbus0: not configured ioapic0 at mainbus0: apid 14 pa 0xfec00000, version 20, 24 pins ioapic1 at mainbus0: apid 13 pa 0xfec82000, version 20, 24 pins ioapic2 at mainbus0: apid 12 pa 0xfec82400, version 20, 24 pins acpiprt0 at acpi0: bus 4 (PCI2) acpiprt1 at acpi0: bus 5 (PCI3) acpiprt2 at acpi0: bus 1 (PCIS) acpiprt3 at acpi0: bus 0 (PCI0) acpicpu0 at acpi0 bios0: ROM list: 0xc0000/0xb000 0xcb000/0x4000 ipmi at mainbus0 not configured pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 "Intel E7520 Host" rev 0x0c "Intel E7520 Error Reporting" rev 0x0c at pci0 dev 0 function 1 not configured ppb0 at pci0 dev 2 function 0 "Intel E7520 PCIE" rev 0x0c pci1 at ppb0 bus 2 ppb1 at pci0 dev 4 function 0 "Intel E7520 PCIE" rev 0x0c pci2 at ppb1 bus 3 ppb2 at pci2 dev 0 function 0 "Intel PCIE-PCIE" rev 0x09 pci3 at ppb2 bus 4 mpi0 at pci3 dev 1 function 0 "Symbios Logic 53c1030" rev 0x08: apic 13 int 4 (irq 11) scsibus0 at mpi0: 16 targets, initiator 7 sd0 at scsibus0 targ 0 lun 0: <LSILOGIC, 1030 IM IM, 1000> SCSI2 0/direct fixed sd0: 139898MB, 512 bytes/sec, 286511104 sec total safte0 at scsibus0 targ 8 lun 0: <IBM, 25P3495a S320 1, 1> SCSI2 3/processor fixed mpi0: phys disk 0 Sync at 160MHz width 16bit offset 127 QAS 0 DT 1 IU 1 mpi0: phys disk 1 Sync at 160MHz width 16bit offset 80 QAS 0 DT 1 IU 1 ppb3 at pci2 dev 0 function 2 "Intel PCIE-PCIE" rev 0x09 pci4 at ppb3 bus 5 ppb4 at pci0 dev 6 function 0 "Intel E7520 PCIE" rev 0x0c pci5 at ppb4 bus 6 bge0 at pci5 dev 0 function 0 "Broadcom BCM5721" rev 0x11, BCM5750 B1 (0x4101): apic 14 int 16 (irq 11), address 00:14:5e:32:98:fa brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0 ppb5 at pci0 dev 7 function 0 "Intel E7520 PCIE" rev 0x0c pci6 at ppb5 bus 7 bge1 at pci6 dev 0 function 0 "Broadcom BCM5721" rev 0x11, BCM5750 B1 (0x4101): apic 14 int 16 (irq 11), address 00:14:5e:32:98:fb brgphy1 at bge1 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0 "Intel E7520 Config" rev 0x0c at pci0 dev 8 function 0 not configured uhci0 at pci0 dev 29 function 0 "Intel 82801EB/ER USB" rev 0x02: apic 14 int 16 (irq 11) uhci1 at pci0 dev 29 function 1 "Intel 82801EB/ER USB" rev 0x02: apic 14 int 19 (irq 3) ehci0 at pci0 dev 29 function 7 "Intel 82801EB/ER USB2" rev 0x02: apic 14 int 23 (irq 5) usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb6 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xc2 pci7 at ppb6 bus 1 vga1 at pci7 dev 1 function 0 "ATI Radeon VE" rev 0x00 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) radeondrm0 at vga1: apic 14 int 16 (irq 11) drm0 at radeondrm0 ichpcib0 at pci0 dev 31 function 0 "Intel 82801EB/ER LPC" rev 0x02 pciide0 at pci0 dev 31 function 2 "Intel 82801EB SATA" rev 0x02: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility atapiscsi0 at pciide0 channel 0 drive 0 scsibus1 at atapiscsi0: 2 targets cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR8083N, 0L02> ATAPI 5/cdrom removable cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 ichiic0 at pci0 dev 31 function 3 "Intel 82801EB/ER SMBus" rev 0x02: apic 14 int 17 (irq 3) iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM registered ECC PC2-3200CL5 spdmem1 at iic0 addr 0x51: 512MB DDR2 SDRAM registered ECC PC2-3200CL5 spdmem2 at iic0 addr 0x52: 512MB DDR2 SDRAM registered ECC PC2-3200CL3 spdmem3 at iic0 addr 0x53: 512MB DDR2 SDRAM registered ECC PC2-3200CL3 usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at ichpcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 mtrr: Pentium Pro MTRR support uhidev0 at uhub2 port 2 configuration 1 interface 0 "Manufacturer KA7175 Adapter" rev 2.00/1.00 addr 2 uhidev0: iclass 3/1 ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 33 wskbd1 at ukbd0 mux 1 wskbd1: connecting to wsdisplay0 uhidev1 at uhub2 port 2 configuration 1 interface 1 "Manufacturer KA7175 Adapter" rev 2.00/1.00 addr 2 uhidev1: iclass 3/1 ums0 at uhidev1: 5 buttons, Z dir wsmouse0 at ums0 mux 0 softraid0 at root root on sd0a swap on sd0b dump on sd0b WARNING: / was not properly unmounted patr...@ceti-a:~[0]$ -- http://www.labyrinthdata.net.au - WA Backup, Dedicated Server and VPS Hosting
