On 2010-08-12, Allan Liblik <[email protected]> wrote:
> Hei!
>
> I can't get SATA disks smart status using atactl command. atactl with
> identify command shows disk model, serial correctly, but readattr
> command don't get nothing and smartstatus returns always "No SMART
> threshold exceeded", irrespective of real SMART values.
>
> NetBSD shows, that disk sd2 have exceeded SMART id5, "reallocated sector
> count", value and computer BIOS shows, that SMART is bad, too.
hmm. I _am_ getting status from drives on an SS4200-E:
<st...@hutch:~:11>$ sudo atactl sd1 readattr
Attributes table revision: 16
ID Attribute name Threshold Value Raw
1 Raw Read Error Rate 51 100 0x000000000000
3 Spin Up Time 11 80 0x000000001a72
4 Start/Stop Count 0 100 0x00000000000c
5 Reallocated Sector Count 10 100 0x000000000000
7 Seek Error Rate 51 253 0x000000000000
8 Seek Time Performance 15 100 0x000000000000
9 Power-On Hours Count 0 98 0x000000002053
10 Spin Retry Count 51 100 0x000000000000
11 Calibration Retry Count 0 100 0x000000000000
12 Device Power Cycle Count 0 100 0x00000000000c
13 Soft Read Error Rate 0 100 0x000000000000
183 Unknown 0 100 0x000000000000
184 Unknown 0 100 0x000000000000
187 Unknown 0 100 0x000000000000
188 Unknown 0 100 0x000000000000
190 Airflow Temperature 0 74 0x00001a0c001a
194 Temperature 0 73 0x0000250c001b
195 Hardware ECC Recovered 0 100 0x00000018c1a7
196 Reallocation Event Count 0 100 0x000000000000
197 Current Pending Sector Count 0 100 0x000000000000
198 Off-Line Scan Uncorrectable Sect 0 100 0x000000000000
199 Ultra DMA CRC Error Count 0 100 0x000000000000
200 Write Error Rate 0 100 0x000000000000
201 Soft Read Error Rate 0 253 0x000000000000
I'm running a newer OS version, I don't recall changes in this area
but may have missed something..
Note that "smartstatus" does not look at the *values*, it asks the drive
if it thinks it is bad. This can come back ok while values are still above
threshold. I'm not sure what the bios looks at. Though the lack of response
from your readattr command definitely indicates something not right.
I suspect it's related to your disks rather than the machine/controller.
OpenBSD 4.7-current (GENERIC) #91: Thu Jul 15 03:04:22 MDT 2010
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC
real mem = 2146238464 (2046MB)
avail mem = 2075283456 (1979MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xfc410 (27 entries)
bios0: vendor American Megatrends Inc. version "V090L" date 12/19/2007
bios0: Intel SS4200-E
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP APIC MCFG OEMB
acpi0: wakeup devices P0P2(S4) P0P1(S4) PS2K(S4) PS2M(S4) MC97(S4) P0P4(S4)
P0P5(S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) USB0(S3) USB1(S3) USB2(S3)
USB3(S3) EUSB(S3)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU 420 @ 1.60GHz, 1600.20 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG
cpu0: 512KB 64b/line 2-way L2 cache
cpu0: apic clock running at 200MHz
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P4)
acpiprt2 at acpi0: bus -1 (P0P5)
acpiprt3 at acpi0: bus 2 (P0P6)
acpiprt4 at acpi0: bus -1 (P0P7)
acpicpu0 at acpi0
acpibtn0 at acpi0: PWRB
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 82945G Host" rev 0x02
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 1 int 16
(irq 10)
pci1 at ppb0 bus 1
em0 at pci1 dev 0 function 0 "Intel PRO/1000MT (82573E)" rev 0x03: apic 1 int
16 (irq 10), address 00:15:17:31:e4:d5
ppb1 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x01: apic 1 int 18
(irq 11)
pci2 at ppb1 bus 2
sili0 at pci2 dev 0 function 0 "CMD Technology SiI3132 SATA" rev 0x01: apic 1
int 18 (irq 11)
scsibus0 at sili0: 2 targets
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 1 int 23
(irq 5)
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 1 int 19
(irq 3)
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 1 int 18
(irq 11)
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 1 int 16
(irq 10)
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 1 int 23
(irq 5)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb2 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci3 at ppb2 bus 3
pcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01
ahci0 at pci0 dev 31 function 2 "Intel 82801GR AHCI" rev 0x01: apic 1 int 19
(irq 3), AHCI 1.1
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, GB0160EAFJE, > SCSI3 0/direct fixed
sd0: 152627MB, 512 bytes/sec, 312581808 sec total
sd1 at scsibus1 targ 2 lun 0: <ATA, SAMSUNG HD103SI, 1AG0> SCSI3 0/direct fixed
sd1: 953869MB, 512 bytes/sec, 1953525168 sec total
sd2 at scsibus1 targ 3 lun 0: <ATA, SAMSUNG HD103SI, 1AG0> SCSI3 0/direct fixed
sd2: 953869MB, 512 bytes/sec, 1953525168 sec total
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 1 int 19
(irq 3)
iic0 at ichiic0
adt0 at iic0 addr 0x2e: sch5027 rev 0x69
spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-5300CL5
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
mtrr: Pentium Pro MTRR support
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
>
> # /sbin/atactl sd2 readattr
>
> # /sbin/atactl sd2 smartstatus
> No SMART threshold exceeded
>
> # /sbin/atactl sd2 smartread
> Off-line data collection:
> status: completed ok
> activity completion time: 600 seconds
> capabilities:
> execute immediate
> read scanning
> self-test routines
> Self-test execution:
> status: completed ok or not started
> recommended polling time:
> short routine: 1 minutes
> extended routine: 175 minutes
> SMART capabilities:
> saving SMART data
> enable/disable attribute autosave
> Error logging: supported
>
> # /sbin/atactl sd2 identify
> Model: ST31000528AS, Rev: CC38, Serial #: 5VP2JJFC
> Device type: ATA, fixed
> Cylinders: 16383, heads: 16, sec/track: 63, total sectors: 1953525168
> Device capabilities:
> ATA standby timer values
> IORDY operation
> IORDY disabling
> Device supports the following standards:
> ATA-4 ATA-5 ATA-6 ATA-7 ATA-8
> Master password revision code 0xfffe
> Device supports the following command sets:
> READ BUFFER command
> WRITE BUFFER command
> Host Protected Area feature set
> Read look-ahead
> Write cache
> Power Management feature set
> Security Mode feature set
> SMART feature set
> Flush Cache Ext command
> Flush Cache command
> Device Configuration Overlay feature set
> 48bit address feature set
> Automatic Acoustic Management feature set
> Set Max security extension commands
> DOWNLOAD MICROCODE command
> SMART self-test
> SMART error logging
> Device has enabled the following command sets/features:
> READ BUFFER command
> WRITE BUFFER command
> Host Protected Area feature set
> Read look-ahead
> Write cache
> Power Management feature set
> SMART feature set
> Flush Cache Ext command
> Flush Cache command
> Device Configuration Overlay feature set
> 48bit address feature set
> Automatic Acoustic Management feature set
> DOWNLOAD MICROCODE command
>
> dmesg:
> OpenBSD 4.7 (GENERIC) #558: Wed Mar 17 20:46:15 MDT 2010
> [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel(R) Celeron(R) CPU 420 @ 1.60GHz ("GenuineIntel" 686-class)
> 1.61 GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
> real mem = 536236032 (511MB)
> avail mem = 510861312 (487MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/19/07, BIOS32 rev. 0 @ 0xf0010,
> SMBIOS rev. 2.5 @ 0xfc410 (27 entries)
> bios0: vendor American Megatrends Inc. version "V090L" date 12/19/2007
> bios0: Intel SS4200-E
> acpi0 at bios0: rev 2
> acpi0: tables DSDT FACP APIC MCFG OEMB
> acpi0: wakeup devices P0P2(S4) P0P1(S4) PS2K(S4) PS2M(S4) MC97(S4)
> P0P4(S4) P0P5(S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) USB0(S3) USB1(S3)
> USB2(S3) USB3(S3) EUSB
> (S3)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: apic clock running at 200MHz
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (P0P4)
> acpiprt2 at acpi0: bus 2 (P0P5)
> acpiprt3 at acpi0: bus 3 (P0P6)
> acpiprt4 at acpi0: bus -1 (P0P7)
> acpicpu0 at acpi0
> acpibtn0 at acpi0: PWRB
> bios0: ROM list: 0xc0000/0xf000
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82945G Host" rev 0x02
> ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 1 int
> 16 (irq 10)
> pci1 at ppb0 bus 1
> em0 at pci1 dev 0 function 0 "Intel PRO/1000MT (82573E)" rev 0x03: apic
> 1 int 16 (irq 10), address 00:15:17:32:1a:73
> ppb1 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x01: apic 1 int
> 17 (irq 11)
> pci2 at ppb1 bus 2
> vga1 at pci2 dev 0 function 0 "ATI Radeon HD 4350" rev 0x00
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> azalia0 at pci2 dev 0 function 1 "ATI Radeon HD 4000 HD Audio" rev 0x00:
> apic 1 int 18 (irq 5)
> azalia0: no supported codecs
> azalia0: initialization failure, detaching
> ppb2 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x01: apic 1 int
> 18 (irq 5)
> pci3 at ppb2 bus 3
> sili0 at pci3 dev 0 function 0 "CMD Technology SiI3132 SATA" rev 0x01:
> apic 1 int 18 (irq 5)
> scsibus0 at sili0: 2 targets
> uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 1 int
> 23 (irq 7)
> uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 1 int
> 19 (irq 3)
> uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 1 int
> 18 (irq 5)
> uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 1 int
> 16 (irq 10)
> ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 1 int
> 23 (irq 7)
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb3 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
> pci4 at ppb3 bus 4
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
> ahci0 at pci0 dev 31 function 2 "Intel 82801GR AHCI" rev 0x01: apic 1
> int 19 (irq 3), AHCI 1.1
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, ST31000528AS, CC38> SCSI3 0/direct fixed
> sd0: 953869MB, 512 bytes/sec, 1953525168 sec total
> sd1 at scsibus1 targ 1 lun 0: <ATA, ST31000528AS, CC38> SCSI3 0/direct fixed
> sd1: 953869MB, 512 bytes/sec, 1953525168 sec total
> sd2 at scsibus1 targ 2 lun 0: <ATA, ST31000528AS, CC38> SCSI3 0/direct fixed
> sd2: 953869MB, 512 bytes/sec, 1953525168 sec total
> sd3 at scsibus1 targ 3 lun 0: <ATA, ST31000528AS, CC38> SCSI3 0/direct fixed
> sd3: 953869MB, 512 bytes/sec, 1953525168 sec total
> ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 1
> int 19 (irq 3)
> iic0 at ichiic0
> adt0 at iic0 addr 0x2e: sch5027 rev 0x69
> spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-5300CL5
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb4 at uhci3: USB revision 1.0
> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> mtrr: Pentium Pro MTRR support
> umass0 at uhub0 port 7 configuration 1 interface 0 "USB2.0 External Mass
> Storage Device" rev 2.00/2.40 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus2 at umass0: 2 targets, initiator 0
> cd0 at scsibus2 targ 1 lun 0: <Slimtype, DVD A DS8A1H, WX13> SCSI0
> 5/cdrom removable
> vscsi0 at root
> scsibus3 at vscsi0: 256 targets
> softraid0 at root
> root on sd0a swap on sd0b dump on sd0b
