The patch titled
pata_sis: Fix and clean up some timing setups
has been removed from the -mm tree. Its filename was
pata_sis-fix-and-clean-up-some-timing-setups.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: pata_sis: Fix and clean up some timing setups
From: Alan Cox <[EMAIL PROTECTED]>
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new
generation controllers in error.
- Use byte size operations where it is cleaner for mode setup
- Fix a couple of masking errors on certai chip revs when setting speeds
Signed-off-by: Alan Cox <[EMAIL PROTECTED]>
Cc: Jeff Garzik <[EMAIL PROTECTED]>
Cc: Tejun Heo <[EMAIL PROTECTED]>
Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
---
drivers/ata/pata_sis.c | 46 +++++++++++++++++++--------------------
1 files changed, 23 insertions(+), 23 deletions(-)
diff -puN drivers/ata/pata_sis.c~pata_sis-fix-and-clean-up-some-timing-setups
drivers/ata/pata_sis.c
--- a/drivers/ata/pata_sis.c~pata_sis-fix-and-clean-up-some-timing-setups
+++ a/drivers/ata/pata_sis.c
@@ -73,14 +73,14 @@ static int sis_short_ata40(struct pci_de
}
/**
- * sis_port_base - return PCI configuration base for dev
+ * sis_old_port_base - return PCI configuration base
for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
* number.
*/
-static int sis_port_base(struct ata_device *adev)
+static int sis_old_port_base(struct ata_device *adev)
{
return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno);
}
@@ -211,7 +211,7 @@ static void sis_set_fifo(struct ata_port
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
@@ -248,7 +248,7 @@ static void sis_old_set_piomode (struct
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
@@ -328,7 +328,7 @@ static void sis_old_set_dmamode (struct
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
@@ -367,7 +367,7 @@ static void sis_66_set_dmamode (struct a
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
@@ -378,12 +378,12 @@ static void sis_66_set_dmamode (struct a
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device, bit 15 udma */
- timing &= ~ 0x870F;
+ timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x6000;
+ timing &= ~0xF000;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
@@ -405,22 +405,22 @@ static void sis_100_set_dmamode (struct
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
- const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200,
0x8100};
+ const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
@@ -440,22 +440,22 @@ static void sis_133_early_set_dmamode (s
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
-
- static const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500,
0x8300, 0x8200, 0x8100};
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+ /* Low 4 bits are timing */
+ static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82,
0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
_
Patches currently in -mm which might be from [EMAIL PROTECTED] are
lots-of-architectures-enable-arbitary-speed-tty-support.patch
git-arm-master.patch
arm26-enable-arbitary-speed-tty-ioctls-and-split.patch
ia64-arbitary-speed-tty-ioctl-support.patch
git-libata-all.patch
libata-fix-hopefully-all-the-remaining-problems-with.patch
testing-patch-for-ali-pata-fixes-hopefully-for-the-problems-with-atapi-dma.patch
pata_ali-more-work.patch
serial-use-resource_size_t-for-port-io-addresses.patch
add-pci_try_set_mwi.patch
fix-pci_find_present.patch
git-scsi-misc.patch
git-watchdog.patch
add-pci_try_set_mwi-prism54pci.patch
xtensa-enable-arbitary-tty-speed-setting-ioctls.patch
blackfin-enable-arbitary-speed-serial-setting.patch
h8300-enable-arbitary-speed-tty-port-setup.patch
m32r-enable-arbitary-speed-tty-rate-setting.patch
etrax-enable-arbitary-speed-setting-on-tty-ports.patch
v850-enable-arbitary-speed-tty-ioctls.patch
doc-kernel-parameters-use-x86-32-tag-instead-of-ia-32.patch
make-proc-tty-drivers-use-seq_list_xxx-helpers.patch
update-zilog-timeout.patch
edd-switch-to-pci_get-based-api.patch
mpu401-warning-fixes.patch
i2o_cfg_passthru-cleanup.patch
i2o_cfg_passthru-cleanup-fix.patch
wrong-memory-access-in-i2o_block_device_lock.patch
i2o-message-leak-in-i2o_msg_post_wait_mem.patch
i2o-proc-reading-oops.patch
i2o-debug-output-cleanup.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
