The patch titled
spi: spi_bfin: resequence DMA start/stop
has been removed from the -mm tree. Its filename was
spi-spi_bfin-resequence-dma-start-stop.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: spi: spi_bfin: resequence DMA start/stop
From: Sonic Zhang <[EMAIL PROTECTED]>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <[EMAIL PROTECTED]>
Signed-off-by: Bryan Wu <[EMAIL PROTECTED]>
Signed-off-by: David Brownell <[EMAIL PROTECTED]>
Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
---
drivers/spi/spi_bfin5xx.c | 30 +++++++++++++++++++-----------
1 file changed, 19 insertions(+), 11 deletions(-)
diff -puN drivers/spi/spi_bfin5xx.c~spi-spi_bfin-resequence-dma-start-stop
drivers/spi/spi_bfin5xx.c
--- a/drivers/spi/spi_bfin5xx.c~spi-spi_bfin-resequence-dma-start-stop
+++ a/drivers/spi/spi_bfin5xx.c
@@ -231,13 +231,13 @@ static int restore_state(struct driver_d
dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");
/* Load the registers */
- cs_deactive(drv_data, chip);
write_BAUD(drv_data, chip->baud);
chip->ctl_reg &= (~BIT_CTL_TIMOD);
chip->ctl_reg |= (chip->width << 8);
write_CTRL(drv_data, chip->ctl_reg);
bfin_spi_enable(drv_data);
+ cs_active(drv_data, chip);
if (ret)
dev_dbg(&drv_data->pdev->dev,
@@ -767,6 +767,7 @@ static void pump_transfers(unsigned long
disable_dma(drv_data->dma_channel);
clear_dma_irqstat(drv_data->dma_channel);
+ bfin_spi_disable(drv_data);
/* config dma channel */
dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
@@ -789,9 +790,6 @@ static void pump_transfers(unsigned long
dev_dbg(&drv_data->pdev->dev,
"doing autobuffer DMA out.\n");
- /* set SPI transfer mode */
- write_CTRL(drv_data, (cr | CFG_SPI_DMAWRITE));
-
/* no irq in autobuffer mode */
dma_config =
(DMAFLOW_AUTO | RESTART | dma_width | DI_EN);
@@ -800,7 +798,13 @@ static void pump_transfers(unsigned long
(unsigned long)drv_data->tx);
enable_dma(drv_data->dma_channel);
- /* just return here, there can only be one transfer in
this mode */
+ /* start SPI transfer */
+ write_CTRL(drv_data,
+ (cr | CFG_SPI_DMAWRITE | BIT_CTL_ENABLE));
+
+ /* just return here, there can only be one transfer
+ * in this mode
+ */
message->status = 0;
giveback(drv_data);
return;
@@ -811,9 +815,6 @@ static void pump_transfers(unsigned long
/* set transfer mode, and enable SPI */
dev_dbg(&drv_data->pdev->dev, "doing DMA in.\n");
- /* set SPI transfer mode */
- write_CTRL(drv_data, (cr | CFG_SPI_DMAREAD));
-
/* clear tx reg soformer data is not shifted out */
write_TDBR(drv_data, 0xFFFF);
@@ -827,12 +828,13 @@ static void pump_transfers(unsigned long
(unsigned long)drv_data->rx);
enable_dma(drv_data->dma_channel);
+ /* start SPI transfer */
+ write_CTRL(drv_data,
+ (cr | CFG_SPI_DMAREAD | BIT_CTL_ENABLE));
+
} else if (drv_data->tx != NULL) {
dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n");
- /* set SPI transfer mode */
- write_CTRL(drv_data, (cr | CFG_SPI_DMAWRITE));
-
/* start dma */
dma_enable_irq(drv_data->dma_channel);
dma_config = (RESTART | dma_width | DI_EN);
@@ -840,6 +842,10 @@ static void pump_transfers(unsigned long
set_dma_start_addr(drv_data->dma_channel,
(unsigned long)drv_data->tx);
enable_dma(drv_data->dma_channel);
+
+ /* start SPI transfer */
+ write_CTRL(drv_data,
+ (cr | CFG_SPI_DMAWRITE | BIT_CTL_ENABLE));
}
} else {
/* IO mode write then read */
@@ -1142,6 +1148,8 @@ static int setup(struct spi_device *spi)
peripheral_request(ssel[spi->master->bus_num]
[chip->chip_select_num-1], DRV_NAME);
+ cs_deactive(drv_data, chip);
+
return 0;
}
_
Patches currently in -mm which might be from [EMAIL PROTECTED] are
origin.patch
libata-set-proper-ata-udma-mode-for-bf548-according-to-system-clock-checkpatch-fixes.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
