The patch titled
spi: spi_bfin cleanups, error handling
has been removed from the -mm tree. Its filename was
spi-spi_bfin-cleanups-error-handling.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: spi: spi_bfin cleanups, error handling
From: Bryan Wu <[EMAIL PROTECTED]>
Cleanup and error handling
- add error handling in SPI bus driver with selecting clients
- use proper defines to access Blackfin MMRs
- remove useless SSYNCs
- cleaner use of portmux calls
Signed-off-by: Michael Hennerich <[EMAIL PROTECTED]>
Signed-off-by: Bryan Wu <[EMAIL PROTECTED]>
Signed-off-by: David Brownell <[EMAIL PROTECTED]>
Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
---
drivers/spi/spi_bfin5xx.c | 109 +++++++++++++++---------------------
1 file changed, 46 insertions(+), 63 deletions(-)
diff -puN drivers/spi/spi_bfin5xx.c~spi-spi_bfin-cleanups-error-handling
drivers/spi/spi_bfin5xx.c
--- a/drivers/spi/spi_bfin5xx.c~spi-spi_bfin-cleanups-error-handling
+++ a/drivers/spi/spi_bfin5xx.c
@@ -59,10 +59,9 @@ MODULE_LICENSE("GPL");
#define DEFINE_SPI_REG(reg, off) \
static inline u16 read_##reg(void) \
- { return *(volatile unsigned short*)(SPI0_REGBASE + off); } \
+ { return bfin_read16(SPI0_REGBASE + off); } \
static inline void write_##reg(u16 v) \
- {*(volatile unsigned short*)(SPI0_REGBASE + off) = v;\
- SSYNC();}
+ {bfin_write16(SPI0_REGBASE + off, v); }
DEFINE_SPI_REG(CTRL, 0x00)
DEFINE_SPI_REG(FLAG, 0x04)
@@ -145,7 +144,6 @@ static void bfin_spi_enable(struct drive
cr = read_CTRL();
write_CTRL(cr | BIT_CTL_ENABLE);
- SSYNC();
}
static void bfin_spi_disable(struct driver_data *drv_data)
@@ -154,7 +152,6 @@ static void bfin_spi_disable(struct driv
cr = read_CTRL();
write_CTRL(cr & (~BIT_CTL_ENABLE));
- SSYNC();
}
/* Caculate the SPI_BAUD register value based on input HZ */
@@ -182,52 +179,44 @@ static int flush(struct driver_data *drv
return limit;
}
+#define MAX_SPI0_SSEL 7
+
/* stop controller and re-config current chip*/
-static void restore_state(struct driver_data *drv_data)
+static int restore_state(struct driver_data *drv_data)
{
struct chip_data *chip = drv_data->cur_chip;
+ int ret = 0;
+ u16 ssel[MAX_SPI0_SSEL] = {P_SPI0_SSEL1, P_SPI0_SSEL2, P_SPI0_SSEL3,
+ P_SPI0_SSEL4, P_SPI0_SSEL5,
+ P_SPI0_SSEL6, P_SPI0_SSEL7,};
/* Clear status and disable clock */
write_STAT(BIT_STAT_CLR);
bfin_spi_disable(drv_data);
dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");
+ /* Load the registers */
+ write_CTRL(chip->ctl_reg);
+ write_BAUD(chip->baud);
+ write_FLAG(chip->flag);
+
if (!chip->chip_select_requested) {
+ int i = chip->chip_select_num;
- dev_dbg(&drv_data->pdev->dev,
- "chip select number is %d\n", chip->chip_select_num);
+ dev_dbg(&drv_data->pdev->dev, "chip select number is %d\n", i);
- switch (chip->chip_select_num) {
- case 1:
- peripheral_request(P_SPI0_SSEL1, DRV_NAME);
- break;
- case 2:
- peripheral_request(P_SPI0_SSEL2, DRV_NAME);
- break;
- case 3:
- peripheral_request(P_SPI0_SSEL3, DRV_NAME);
- break;
- case 4:
- peripheral_request(P_SPI0_SSEL4, DRV_NAME);
- break;
- case 5:
- peripheral_request(P_SPI0_SSEL5, DRV_NAME);
- break;
- case 6:
- peripheral_request(P_SPI0_SSEL6, DRV_NAME);
- break;
- case 7:
- peripheral_request(P_SPI0_SSEL7, DRV_NAME);
- break;
- }
+ if ((i > 0) && (i <= MAX_SPI0_SSEL))
+ ret = peripheral_request(ssel[i-1], DRV_NAME);
chip->chip_select_requested = 1;
}
- /* Load the registers */
- write_CTRL(chip->ctl_reg);
- write_BAUD(chip->baud);
- write_FLAG(chip->flag);
+ if (ret)
+ dev_dbg(&drv_data->pdev->dev,
+ ": request chip select number %d failed\n",
+ chip->chip_select_num);
+
+ return ret;
}
/* used to kick off transfer in rx mode */
@@ -285,7 +274,6 @@ static void u8_cs_chg_writer(struct driv
while (drv_data->tx < drv_data->tx_end) {
write_FLAG(chip->flag);
- SSYNC();
write_TDBR(*(u8 *) (drv_data->tx));
while (read_STAT() & BIT_STAT_TXS)
@@ -293,13 +281,13 @@ static void u8_cs_chg_writer(struct driv
while (!(read_STAT() & BIT_STAT_SPIF))
continue;
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
++drv_data->tx;
}
write_FLAG(0xFF00);
- SSYNC();
+
}
static void u8_reader(struct driver_data *drv_data)
@@ -331,7 +319,6 @@ static void u8_cs_chg_reader(struct driv
while (drv_data->rx < drv_data->rx_end) {
write_FLAG(chip->flag);
- SSYNC();
read_RDBR(); /* kick off */
while (!(read_STAT() & BIT_STAT_RXS))
@@ -340,13 +327,13 @@ static void u8_cs_chg_reader(struct driv
continue;
*(u8 *) (drv_data->rx) = read_SHAW();
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
++drv_data->rx;
}
write_FLAG(0xFF00);
- SSYNC();
+
}
static void u8_duplex(struct driver_data *drv_data)
@@ -370,7 +357,7 @@ static void u8_cs_chg_duplex(struct driv
while (drv_data->rx < drv_data->rx_end) {
write_FLAG(chip->flag);
- SSYNC();
+
write_TDBR(*(u8 *) (drv_data->tx));
while (!(read_STAT() & BIT_STAT_SPIF))
@@ -379,14 +366,14 @@ static void u8_cs_chg_duplex(struct driv
continue;
*(u8 *) (drv_data->rx) = read_RDBR();
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
++drv_data->rx;
++drv_data->tx;
}
write_FLAG(0xFF00);
- SSYNC();
+
}
static void u16_writer(struct driver_data *drv_data)
@@ -412,7 +399,6 @@ static void u16_cs_chg_writer(struct dri
while (drv_data->tx < drv_data->tx_end) {
write_FLAG(chip->flag);
- SSYNC();
write_TDBR(*(u16 *) (drv_data->tx));
while ((read_STAT() & BIT_STAT_TXS))
@@ -420,13 +406,12 @@ static void u16_cs_chg_writer(struct dri
while (!(read_STAT() & BIT_STAT_SPIF))
continue;
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
drv_data->tx += 2;
}
write_FLAG(0xFF00);
- SSYNC();
}
static void u16_reader(struct driver_data *drv_data)
@@ -454,7 +439,6 @@ static void u16_cs_chg_reader(struct dri
while (drv_data->rx < drv_data->rx_end) {
write_FLAG(chip->flag);
- SSYNC();
read_RDBR(); /* kick off */
while (!(read_STAT() & BIT_STAT_RXS))
@@ -463,13 +447,12 @@ static void u16_cs_chg_reader(struct dri
continue;
*(u16 *) (drv_data->rx) = read_SHAW();
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
drv_data->rx += 2;
}
write_FLAG(0xFF00);
- SSYNC();
}
static void u16_duplex(struct driver_data *drv_data)
@@ -493,7 +476,6 @@ static void u16_cs_chg_duplex(struct dri
while (drv_data->tx < drv_data->tx_end) {
write_FLAG(chip->flag);
- SSYNC();
write_TDBR(*(u16 *) (drv_data->tx));
while (!(read_STAT() & BIT_STAT_SPIF))
@@ -502,14 +484,13 @@ static void u16_cs_chg_duplex(struct dri
continue;
*(u16 *) (drv_data->rx) = read_RDBR();
write_FLAG(0xFF00 | chip->flag);
- SSYNC();
+
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
drv_data->rx += 2;
drv_data->tx += 2;
}
write_FLAG(0xFF00);
- SSYNC();
}
/* test if ther is more transfer to be done */
@@ -811,7 +792,6 @@ static void pump_transfers(unsigned long
"IO duplex: cr is 0x%x\n", cr);
write_CTRL(cr);
- SSYNC();
drv_data->duplex(drv_data);
@@ -826,7 +806,6 @@ static void pump_transfers(unsigned long
"IO write: cr is 0x%x\n", cr);
write_CTRL(cr);
- SSYNC();
drv_data->write(drv_data);
@@ -841,7 +820,6 @@ static void pump_transfers(unsigned long
"IO read: cr is 0x%x\n", cr);
write_CTRL(cr);
- SSYNC();
drv_data->read(drv_data);
if (drv_data->rx != drv_data->rx_end)
@@ -892,6 +870,14 @@ static void pump_messages(struct work_st
/* Extract head of queue */
drv_data->cur_msg = list_entry(drv_data->queue.next,
struct spi_message, queue);
+
+ /* Setup the SSP using the per chip configuration */
+ drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
+ if (restore_state(drv_data)) {
+ spin_unlock_irqrestore(&drv_data->lock, flags);
+ return;
+ };
+
list_del_init(&drv_data->cur_msg->queue);
/* Initial message state */
@@ -899,13 +885,10 @@ static void pump_messages(struct work_st
drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
struct spi_transfer, transfer_list);
- /* Setup the SSP using the per chip configuration */
- drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
- restore_state(drv_data);
- dev_dbg(&drv_data->pdev->dev,
- "got a message to pump, state is set to: baud %d, flag 0x%x,
ctl 0x%x\n",
- drv_data->cur_chip->baud, drv_data->cur_chip->flag,
- drv_data->cur_chip->ctl_reg);
+ dev_dbg(&drv_data->pdev->dev, "got a message to pump, "
+ "state is set to: baud %d, flag 0x%x, ctl 0x%x\n",
+ drv_data->cur_chip->baud, drv_data->cur_chip->flag,
+ drv_data->cur_chip->ctl_reg);
dev_dbg(&drv_data->pdev->dev,
"the first transfer len is %d\n",
_
Patches currently in -mm which might be from [EMAIL PROTECTED] are
origin.patch
git-mtd.patch
blackfin-serial-driver-this-driver-enable-sports-on-blackfin-emulate-uart.patch
kernel-printkc-concerns-about-the-console-handover.patch
remove-mm_ptovvtop.patch
blackfin-rtc-driver-the-frequency-function-is-in-units-of-hz-not-units-of-seconds-so-lock-our-driver-down-to-1-hz.patch
blackfin-rtc-driver-we-pass-in-a-struct-device-to-the-irq-handler-not-a-struct-platform_device-so-fix-the-irq-handler.patch
blackfin-rtc-driver-cleanup-proc-handler-we-dont-need-rtc-reg-dump-now-that-we-have-mmr-filesystem-in-sysfs.patch
blackfin-rtc-driver-use-dev_dbg-rather-than-pr_stamp.patch
blackfin-rtc-driver-read_alarm-checks-the-enabled-field-not-the-pending-field.patch
blackfin-rtc-driver-shave-off-another-memcpy-by-using-assignment.patch
blackfin-rtc-driver-convert-sync-wait-to-use-the-irq-write-complete-notice.patch
sanitize-the-type-of-struct-useru_ar0.patch
add-cmpxchg_local-to-blackfin-replace-__cmpxchg-by-generic-cmpxchg.patch
d_path-make-d_path-use-a-struct-path.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
