The patch titled
atmel_spi: fix clock polarity
has been added to the -mm tree. Its filename is
atmel_spi-fix-clock-polarity.patch
Before you just go and hit "reply", please:
a) Consider who else should be cc'ed
b) Prefer to cc a suitable mailing list as well
c) Ideally: find the original patch on the mailing list and do a
reply-to-all to that, adding suitable additional cc's
*** Remember to use Documentation/SubmitChecklist when testing your code ***
See http://www.zip.com.au/~akpm/linux/patches/stuff/added-to-mm.txt to find
out what to do about this
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: atmel_spi: fix clock polarity
From: Atsushi Nemoto <[EMAIL PROTECTED]>
I found that atmel_spi driver does not initialize clock polarity correctly
(except for at91rm9200 CS0 channel) in some cases.
The atmel_spi driver uses gpio-controlled chipselect. OTOH spi clock
signal is controlled by CSRn.CPOL bit, but this register controls clock
signal correctly only in 'real transfer' duration. At the time of
cs_activate() call, CSRn.CPOL will be initialized correctly, but the
controller do not know which channel is to be used next, so clock signal
will stay at the inactive state of last transfer. If clock polarity of new
transfer and last transfer was differ, new transfer will start with wrong
clock signal state.
For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be
low. Of course this will violates SPI transfer.
Here is my quick workaround for this problem. It makes all CSRn.CPOL match
for the transfer before activating chip select.
Cc: Haavard Skinnemoen <[EMAIL PROTECTED]>
Cc: David Brownell <[EMAIL PROTECTED]>
Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
---
drivers/spi/atmel_spi.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff -puN drivers/spi/atmel_spi.c~atmel_spi-fix-clock-polarity
drivers/spi/atmel_spi.c
--- a/drivers/spi/atmel_spi.c~atmel_spi-fix-clock-polarity
+++ a/drivers/spi/atmel_spi.c
@@ -87,6 +87,16 @@ static void cs_activate(struct atmel_spi
unsigned gpio = (unsigned) spi->controller_data;
unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
+ int i;
+ u32 csr;
+ u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
+
+ /* Make sure clock polarity is correct */
+ for (i = 0; i < spi->master->num_chipselect; i++) {
+ csr = spi_readl(as, CSR0 + 4 * i);
+ if ((csr ^ cpol) & SPI_BIT(CPOL))
+ spi_writel(as, CSR0 + 4 * i, csr ^ SPI_BIT(CPOL));
+ }
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
_
Patches currently in -mm which might be from [EMAIL PROTECTED] are
git-watchdog.patch
atmel_spi-fix-clock-polarity.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
