Hey Steven,
On Tue, Mar 22, 2016 at 6:44 AM, Steven Pease <spe...@suitabletech.com> wrote: > Hi, > I'm trying to get the MC7455 working with kernel 4.4.5 or 4.4.6. My > workstation is running Arch which is using kernel 4.4.5 and > ModemManager 1.4.12. In the following, the modem is the only modem on > the system at index 1 since this is the second try following a reboot. > > I'm trying to get an internet connect (IPV4) going over the modem. The > IMEI and Phone # appear to be correct although I've X'd them out. You won't be able to get a proper connection unless you use ModemManager from git master or the new 1.6-rc1 tagged last week. This is because the MC7455 requires the "raw-ip" only setup. BUT not having that newer MM isn't the only issue. See below. > > $ mmcli -m 1 > /org/freedesktop/ModemManager1/Modem/1 (device id > '3abb9e13c07a07a53a0e4f5881b52cd195f21502') > ------------------------- > Hardware | manufacturer: 'Sierra Wireless, Incorporated' > | model: 'MC7455' > | revision: 'SWI9X30C_02.04.07.00 r4823 > CARMD-EV-FRMWR2 2015/11/04 06:51:37' > | supported: 'gsm-umts, lte' > | current: 'gsm-umts, lte' > | equipment id: 'XXXXXXXXXXXXXXX' > ------------------------- > System | device: '/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-5' > | drivers: 'qmi_wwan, qcserial' > | plugin: 'Gobi' > | primary port: 'ttyUSB2' > | ports: 'ttyUSB0 (qcdm), ttyUSB2 (at), > wwp0s29f7u5i10 (net), wwp0s29f7u5i8 (net)' You're missing here the cdc-wdm ports to talk QMI. Is this a self-compiled kernel? Is the cdc-wdm driver enabled in the build? > ------------------------- > Numbers | own : 'XXXXXXXXXXX' > ------------------------- > Status | lock: 'none' > | unlock retries: 'unknown' > | state: 'disabled' > | power state: 'on' > | access tech: 'unknown' > | signal quality: '0' (cached) > ------------------------- > Modes | supported: 'allowed: 2g, 3g, 4g; preferred: none' > | current: 'allowed: 2g, 3g, 4g; preferred: none' > ------------------------- > Bands | supported: 'unknown' > | current: 'unknown' > ------------------------- > IP | supported: 'ipv4, ipv6, ipv4v6' > ------------------------- > 3GPP | imei: 'XXXXXXXXXXXXXXX' > | enabled locks: 'none' > | operator id: 'unknown' > | operator name: 'unknown' > | subscription: 'unknown' > | registration: 'unknown' > ------------------------- > SIM | path: '/org/freedesktop/ModemManager1/SIM/1' > > ------------------------- > Bearers | paths: 'none' > > $ mmcli -m 1 --simple-connect="apn=broadband,ip-type=ipv4v6" --verbose > --timeout=1500 > [21 Mar 2016, 22:31:19] [Debug] Forcing request to be run asynchronously > [21 Mar 2016, 22:31:19] [Debug] Assuming '1' is the modem index > [21 Mar 2016, 22:31:19] [Debug] ModemManager process found at ':1.31' > [21 Mar 2016, 22:31:19] [Debug] Modem found at > '/org/freedesktop/ModemManager1/Modem/1' > > [21 Mar 2016, 22:31:19] [Debug] Asynchronously connecting the modem... > successfully connected the modem > > $ mmcli -b 1 > Bearer '/org/freedesktop/ModemManager1/Bearer/1' > ------------------------- > Status | connected: 'yes' > | suspended: 'no' > | interface: 'ttyUSB2' > | IP timeout: '20' This should have listed one of the WWANs, but it's not there because the QMI implementation isn't managing the modem, due to the lack of cdc-wdm port. > ------------------------- > Properties | apn: 'broadband' > | roaming: 'allowed' > | IP type: 'ipv4v6' > | user: 'none' > | password: 'none' > | number: 'none' > | Rm protocol: 'unknown' > ------------------------- > IPv4 configuration | method: 'ppp' > | address: 'unknown' > | prefix: '0' > | gateway: 'unknown' > | DNS: none > ------------------------- > IPv6 configuration | method: 'ppp' > | address: 'unknown' > | prefix: '0' > | gateway: 'unknown' > | DNS: none > > Trying to get a lease from either wwan interface fails: > > $ sudo dhcpcd wwp0s29f7u5i8 > wwp0s29f7u5i8: waiting for carrier > wwp0s29f7u5i8: carrier acquired > wwp0s29f7u5i8: adding address fe80::aa33:9c69:b4fa:2796 > DUID XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX > wwp0s29f7u5i8: IAID df:90:dc:bc > wwp0s29f7u5i8: soliciting a DHCP lease > wwp0s29f7u5i8: soliciting an IPv6 router > wwp0s29f7u5i8: no IPv6 Routers available > timed out > dhcpcd exited > > $ sudo dhcpcd wwp0s29f7u5i10 > wwp0s29f7u5i10: waiting for carrier > wwp0s29f7u5i10: carrier acquired > wwp0s29f7u5i10: adding address fe80::f614:fdf:279f:ae6c > DUID XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX > wwp0s29f7u5i10: IAID 67:d6:ab:9b > wwp0s29f7u5i10: soliciting a DHCP lease > wwp0s29f7u5i10: soliciting an IPv6 router > wwp0s29f7u5i10: no IPv6 Routers available > timed out > dhcpcd exited > No, you cannot do this if the bearer info doesn't list a WWAN. > I'm guessing I need to get MM to start the bearer on wwp0s29f7u5i10 > instead of ttyUSB2, but so far I haven't figured out how to do this. This should be automatic, only if MM grabbed all the required ports. -- Aleksander https://aleksander.es _______________________________________________ ModemManager-devel mailing list ModemManager-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/modemmanager-devel
