Some modems offer a DHCP emulation in their firmware. Others don't. And this
information should be seen when you look at the bearer that gets created when
you connect the modem.
mmcli -m <modem num> # should list bearers
mmcli -b <bearer_number> # should tell you the config method
Maybe the modem corresponding to wwan1 has a "static" configuration method,
assuming wwan1 doesn't pertain to the same modem exposing wwan0.
If the configuration method is "static", you should somehow configure the
modem, with the ip command or whatever fits.
Maybe NetworkManager could be a solution for your use-case? I don't know, just
proposing here.
Enrico
On Sat, 2 Oct 2021, Lucas Pelegrino wrote:
Date: Sat, 2 Oct 2021 23:21:22
From: Lucas Pelegrino <lucas....@gmail.com>
To: Yegor Yefremov <yegorsli...@googlemail.com>
Cc: "ModemManager (development)" <modemmanager-devel@lists.freedesktop.org>
Subject: Re: Modem connected but no internet
Just to give some more information. When I do `dhclient wwan0` I can see a new
route being added and wwan0 works:
$ ip route show
default via 100.72.135.138 dev wwan0
default via 192.168.0.1 dev wlan0 metric 1
default via 192.168.0.1 dev wlan0 proto dhcp metric 600
100.72.135.136/30 dev wwan0 proto kernel scope link src 100.72.135.137
100.73.179.140/30 dev wwan1 proto kernel scope link src 100.73.179.142 metric
700
192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.16
But if I do `dhclient wwan1` nothing changes on the `ip route show`. I don't
understand much about networks, but I guess I can only have one route set? I
think `dhclient` might not be the issue. Any information is appreciated.
Em sáb., 2 de out. de 2021 às 12:03, Lucas Pelegrino <lucas....@gmail.com>
escreveu:
I tried running `sudo dhclient wwan0`, it seems it got one of the modems
to work, but I have two modems and `wwan1` remains with the same problem and
`sudo dhclient wwan1` didn't seem to work on it.
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN
group default qlen 1000
link/ether b8:27:eb:87:22:8e brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether b8:27:eb:d2:77:db brd ff:ff:ff:ff:ff:ff
inet 192.168.0.16/24 brd 192.168.0.255 scope global dynamic noprefixroute wlan0
valid_lft 85555sec preferred_lft 85555sec
inet6 2804:14c:7582:46bf::1007/128 scope global dynamic noprefixroute
valid_lft 85557sec preferred_lft 85557sec
inet6 2804:14c:7582:46bf:cfbe:7945:f701:da92/64 scope global dynamic
noprefixroute
valid_lft 86372sec preferred_lft 71972sec
inet6 fe80::5139:cd08:a2a9:9a4e/64 scope link noprefixroute
valid_lft forever preferred_lft forever
4: wwan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state
UNKNOWN group default qlen 1000
link/ether 0c:5b:8f:27:9a:64 brd ff:ff:ff:ff:ff:ff
inet 100.70.243.89/30 brd 100.70.243.91 scope global noprefixroute wwan0
valid_lft forever preferred_lft forever
6: wwan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state
UNKNOWN group default qlen 1000
link/ether 0c:5b:8f:27:9a:64 brd ff:ff:ff:ff:ff:ff
inet 100.71.207.216/28 brd 100.71.207.223 scope global dynamic wwan1
valid_lft 518326sec preferred_lft 518326sec
Em sáb., 2 de out. de 2021 às 11:36, Yegor Yefremov
<yegorsli...@googlemail.com> escreveu:
Hi Lucas,
On Sat, Oct 2, 2021 at 4:26 PM Lucas Pelegrino <lucas....@gmail.com>
wrote:
>
> Hello there.
>
> I have this behavior in my raspberry PI where a modem shows connected,
but I still can't connect to the internet:
> --------------------------------
> General | path: /org/freedesktop/ModemManager1/Modem/4
> | device id: ab1573a4186ee4930c3dbe7ee14e2dddcd10b4c2
> --------------------------------
> Hardware | manufacturer: huawei
> | model: E3276
> | firmware revision: 21.260.05.01.150
> | supported: gsm-umts
> | current: gsm-umts
> | equipment id: 866519011156587
> --------------------------------
> System | device:
/sys/devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2.2
> | drivers: huawei_cdc_ncm, option
> | plugin: huawei
> | primary port: cdc-wdm0
> | ports: cdc-wdm0 (at), ttyUSB0 (at), ttyUSB1 (at), wwan0 (net)
> --------------------------------
> Numbers | own: +xxxx
> --------------------------------
> Status | unlock retries: sim-pin (3), sim-puk (10), sim-pin2 (3),
sim-puk2 (10)
> | state: connected
> | power state: on
> | access tech: umts
> | signal quality: 41% (recent)
> --------------------------------
> Modes | supported: allowed: 2g; preferred: none
> | allowed: 3g; preferred: none
> | allowed: 4g; preferred: none
> | allowed: 2g, 3g, 4g; preferred: none
> | current: allowed: 2g, 3g, 4g; preferred: none
> --------------------------------
> IP | supported: ipv4, ipv6, ipv4v6
> --------------------------------
> 3GPP | imei: 866519011156587
> | operator id: 72416
> | operator name: Oi
> | registration: roaming
> --------------------------------
> 3GPP EPS | ue mode of operation: csps-2
> --------------------------------
> SIM | primary sim path: /org/freedesktop/ModemManager1/SIM/4
> --------------------------------
> Bearer | paths: /org/freedesktop/ModemManager1/Bearer/5
>
>
>
> Weird thing is that on my Ubuntu desktop this modem works! The only
difference I noticed is that in my Ubuntu field 'access tech' is 'lte', while
above (on the pi) like you can see it's 'umts'.
>
> I figured the problem might be related to the 'access tech' field
above, so I tried forcing setting mode for '4g' but didn't work:
>
> $ sudo mmcli -m 4 --set-allowed-modes='4g' --set-preferred-mode='4g'
> error: couldn't set current modes:
'GDBus.Error:org.freedesktop.ModemManager1.Error.Core.Unsupported: The given
combination of allowed and preferred modes is not supported'
>
>
> The only difference between my raspberry pi and my desktop machine is
that the pi is under a more recent version of ModemManager 1.16 vs 1.12 from my
desktop Ubuntu.
>
> Any ideas?
Could you share your IP configuration i.e. please post the output of
the "ip addr" command. Looks like you haven't run dhcpclient or alike
on your wwan0 interface.
Best regards,
Yegor
