Send Motion-user mailing list submissions to
motion-user@lists.sourceforge.net
To subscribe or unsubscribe via the World Wide Web, visit
https://lists.sourceforge.net/lists/listinfo/motion-user
or, via email, send a message with subject or body 'help' to
motion-user-requ...@lists.sourceforge.net
You can reach the person managing the list at
motion-user-ow...@lists.sourceforge.net
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Motion-user digest..."
Today's Topics:
1. Re: Where did "output_secondary_pictures" and
"output_both_pictures" go? (Ronnie McMaster)
2. Re: Where did "output_secondary_pictures" and
"output_both_pictures" go? (Jean Fahrtmann)
----------------------------------------------------------------------
Message: 1
Date: Sat, 22 Jun 2019 09:35:13 -0600
From: Ronnie McMaster <ronnie.mcmas...@gmail.com>
To: Motion discussion list <motion-user@lists.sourceforge.net>
Subject: Re: [Motion-user] Where did "output_secondary_pictures" and
"output_both_pictures" go?
Message-ID:
<caa8w+k76aetf26x_xudaftqgsour9cx2j5uanst8d9kl6uk...@mail.gmail.com>
Content-Type: text/plain; charset="utf-8"
In what version were you using those? This page doesn't show those listed
for anything Version 3.2 or newer.
https://motion-project.github.io/motion_config.html#
Thanks,
Ronnie McMaster
On Sat, Jun 22, 2019 at 4:39 AM Jean Fahrtmann via Motion-user <
motion-user@lists.sourceforge.net> wrote:
> Hi, some time ago there were a few commands in motion-mmalcam.conf like
>
>
>
> output_secondary_pictures
>
>
>
> and
>
>
>
> output_both_pictures
>
>
>
> They were meant to achieve
>
>
>
> # Output pictures from secondary capture (see
> mmalcam_secondary_buffer_upscale above)
>
> # Use this to perform motion detection on a low-res image and record a
> high-res output
>
>
>
> The options saved both resolutions as ?.jpg? and ?.JPG?.
>
>
>
> In the current version of motion I can?t find these things anymore. If I
> add them, there is no effect at all.
>
>
>
> Any clue?
>
>
>
> Help will be very much appreciated!
>
>
>
> Best regards?.
> _______________________________________________
> Motion-user mailing list
> Motion-user@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
-------------- next part --------------
An HTML attachment was scrubbed...
------------------------------
Message: 2
Date: Sat, 22 Jun 2019 22:23:49 +0200
From: "Jean Fahrtmann" <jean.fahrtm...@yahoo.de>
To: "'Motion discussion list'" <motion-user@lists.sourceforge.net>
Subject: Re: [Motion-user] Where did "output_secondary_pictures" and
"output_both_pictures" go?
Message-ID: <001801d52938$677ab4e0$36701ea0$@yahoo.de>
Content-Type: text/plain; charset="utf-8"
Hi Ronnie,
I don?t know the version, I believe I installed it a few yeras ago from
motion-mmal-lowflyerUK-20151114.tar.gz
and it runs perfectly on a Pi 2 and Pi 3, but unfortunately not on a Pi 3B+.
There it generates a ?segmentation fault?. The new versions of motion run
perfectly, too, but without the b. m. options.
If it is of any help? I uploaded motion-mmal-lowflyerUK-20151114.tar.gz to my
dropbox:
https://www.dropbox.com/sh/ysis40zt5zj7ht9/AAC1-unmvw0el9TZjw1Yrv0va?dl=0
Thanks for any help!
Best regards,
Jean
Von: Ronnie McMaster [mailto:ronnie.mcmas...@gmail.com]
Gesendet: Samstag, 22. Juni 2019 17:35
An: Motion discussion list <motion-user@lists.sourceforge.net>
Betreff: Re: [Motion-user] Where did "output_secondary_pictures" and
"output_both_pictures" go?
In what version were you using those? This page doesn't show those listed for
anything Version 3.2 or newer.
https://motion-project.github.io/motion_config.html#
<https://motion-project.github.io/motion_config.html>
Thanks,
Ronnie McMaster
On Sat, Jun 22, 2019 at 4:39 AM Jean Fahrtmann via Motion-user
<motion-user@lists.sourceforge.net <mailto:motion-user@lists.sourceforge.net> >
wrote:
Hi, some time ago there were a few commands in motion-mmalcam.conf like
output_secondary_pictures
and
output_both_pictures
They were meant to achieve
# Output pictures from secondary capture (see mmalcam_secondary_buffer_upscale
above)
# Use this to perform motion detection on a low-res image and record a high-res
output
The options saved both resolutions as ?.jpg? and ?.JPG?.
In the current version of motion I can?t find these things anymore. If I add
them, there is no effect at all.
Any clue?
Help will be very much appreciated!
Best regards?.
_______________________________________________
Motion-user mailing list
Motion-user@lists.sourceforge.net <mailto:Motion-user@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/motion-user
https://motion-project.github.io/
Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
-------------- next part --------------
An HTML attachment was scrubbed...
------------------------------
------------------------------
Subject: Digest Footer
_______________________________________________
Motion-user mailing list
Motion-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/motion-user
------------------------------
End of Motion-user Digest, Vol 156, Issue 34
********************************************
