I have installed kfir drivers correctly but when I cat /dev/video >x.mpg
there is a seg fault.
Here the details:
Linux version 2.4.2-22mdk ([EMAIL PROTECTED]) (gcc version
egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Thu Mar 29 18:11:30 CEST
2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=801
Initializing CPU#0
Detected 996.664 MHz processor.
Console: colour VGA+ 80x43
Calibrating delay loop... 1985.74 BogoMIPS
Memory: 126516k/131008k available (948k kernel code, 4104k reserved, 356k
data, 224k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.39 (20010312) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb130, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Bus master Pipeline request disabled
PCI: Disabled enhanced CPU to PCI writes
PCI: Post Write Fail set to Retry
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 84021kB/28007kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
hda: QUANTUM FIREBALLP AS20.5, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 40132503 sectors (20548 MB) w/1902KiB Cache, CHS=2498/255/63, UDMA(100)
Partition check:
hda: hda1
RAMDISK: Compressed image found at block 0
Uncompressing.......done.
Freeing initrd memory: 125k freed
Serial driver version 5.02 (2000-08-09) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
IP-Config: No network devices available.
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
PCI: Found IRQ 11 for device 00:0a.0
PCI: The same IRQ used for device 00:0e.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.5
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Wide Channel A, SCSI Id=7, 32/255 SCBs
Vendor: IBM Model: DDYS-T18350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
Vendor: PLEXTOR Model: CD-R PX-W124TS Rev: 1.04
Type: CD-ROM ANSI SCSI revision: 02
scsi0:0:0:0: Tagged Queuing enabled. Depth 8
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB)
sda: sda1
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 224k freed
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.65 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.65 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.65 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.65 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
es1371: version v0.30 time 16:25:11 Apr 19 2001
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
PCI: Found IRQ 9 for device 00:09.0
es1371: found es1371 rev 6 at io 0xdc00 irq 9
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Linux video capture interface: v1.00
i2c: initialized
Zoran ZR36060 + ZR36057/67 MJPEG board driver version 0.8
No known MJPEG cards found.
8139too Fast Ethernet driver 0.9.15c loaded
PCI: Found IRQ 10 for device 00:0b.0
eth0: RealTek RTL8139 Fast Ethernet at 0xc88ba000, 00:50:fc:03:6b:f7, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139B'
eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability
40a1.
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Via 686A parallel port: io=0x378, irq=7
lp0: using parport0 (interrupt-driven).
lp0: console ready
...
kfir: i2c detach [SAA7113]
i2c-core.o: client [SAA7113] unregistered.
i2c-core.o: adapter unregistered: kfir #0
kfir: Kfir board revision 5e
kfir: Reset Altera
kfir: done
kfir: Reset Kfir and PLL ... done
kfir: ADSP loading successful
kfir: ADSP initialization...done
kfir: segment: 0 Done
kfir: segment: 1 Done
kfir: segment: 2 Done
kfir: segment: 3 Done
kfir: segment: 4 Done
kfir: segment: 5 Done
kfir: done
saa7113: version=11
saa7113: attaching SAA7113 at 0x4a
kfir: saa7113 decoder attached
kfir: i2c attach [SAA7113]
i2c-core.o: client [SAA7113] registered to adapter [kfir #0](pos. 0).
saa7113: status=c0
saa7113: attached to adapter kfir #0
i2c-core.o: adapter kfir #0 registered as adapter 0.
kfir: Found i2c device at: 0x4a
kfir: decoder status=4
kfir: kfir_remove_one()
kfir: i2c detach [SAA7113]
i2c-core.o: client [SAA7113] unregistered.
i2c-core.o: adapter unregistered: kfir #0
kfir: Kfir board revision 5e
loaded microcode with length 32385
kfir: Reset Altera
kfir: done
kfir: Reset Kfir and PLL ... done
kfir: ADSP loading successful
kfir: ADSP initialization...done
kfir: segment: 0 Done
kfir: segment: 1 Done
kfir: segment: 2 Done
kfir: segment: 3 Done
kfir: segment: 4 Done
kfir: segment: 5 Done
kfir: Download parameters...kfir: done
saa7113: version=11
saa7113: attaching SAA7113 at 0x4a
kfir: saa7113 decoder attached
kfir: i2c attach [SAA7113]
i2c-core.o: client [SAA7113] registered to adapter [kfir #0](pos. 0).
saa7113: status=c0
saa7113: attached to adapter kfir #0
i2c-core.o: adapter kfir #0 registered as adapter 0.
kfir: Found i2c device at: 0x4a
kfir: decoder status=4
...
when I cat /dev/video >x.mpg:
Unable to handle kernel paging request at virtual address 7269665b
printing eip:
c8898191
*pde = 00000000
Oops: 0002
CPU: 0
EIP: 0010:[<c8898191>]
EFLAGS: 00010206
eax: 7269664b ebx: c8907a20 ecx: 00000019 edx: c8898000
esi: 00000000 edi: c8898e40 ebp: c7f445a0 esp: c4c37f1c
ds: 0018 es: 0018 ss: 0018
Process cat (pid: 1632, stackpage=c4c37000)
Stack: 00000000 c734af20 c5cbb0a0 00000000 00008001 c0138967 c5cbb0a0
00000004
c012f45d c5cbb0a0 c734af20 c734af20 c5cbb0a0 ffffffe9 c012e58e
c5cbb0a0
c734af20 00008000 00000003 00000000 c6421000 c012e4c3 c6b84ca0
c7f445a0
Call Trace: [<c0138967>] [<c012f45d>] [<c012e58e>] [<c012e4c3>] [<c012e7dc>]
[<c0106f73>]
Code: ff 40 10 8b 03 80 48 14 18 8b 43 2c 85 c0 74 2f 6a 00 53 ff
Is the decoder status = 4 the key of solution??
I have attached correctly Svideo in, selected in insmod vidinput=1.
Thank you.
