Here is my config for a PIX ver 6.2(2) I do not have info on failover, but is on my todo list so if anyone has done it on ver6.2(2) I would be interested in seeing how.....
Thanks KLW ### PIX CPU Load (1 min & 5 min) report for 10.x.x.x ### Target[10.1.0.22_0_CPU1]: 1.3.6.1.4.1.9.9.109.1.1.1.1.4.1&1.3.6.1.4.1.9.9.109.1.1.1.1.5.1:[EMAIL PROTECTED] .1.0.22::2:2::1 Options[10.1.0.22_0_CPU1]: gauge,nopercent,growright,nobanner,integer WithPeak[10.1.0.22_0_CPU1]: wmy YLegend[10.1.0.22_0_CPU1]: Util(percent) MaxBytes[10.1.0.22_0_CPU1]: 100 LegendI[10.1.0.22_0_CPU1]: CPU Usage (5 secs) LegendO[10.1.0.22_0_CPU1]: CPU Usage (1 min) Title[10.1.0.22_0_CPU1]: PIX Unscaled[10.1.0.22_0_CPU1]: dwmy Legend1[10.1.0.22_0_CPU1]: CPU utilisation over 1 minute Legend2[10.1.0.22_0_CPU1]: CPU utilisation over 5 minute Legend3[10.1.0.22_0_CPU1]: Maximal CPU utilisation over 1 minute Legend4[10.1.0.22_0_CPU1]: Maximal CPU utilisation over 5 minute ShortLegend[10.1.0.22_0_CPU1]: % PageTop[10.1.0.22_0_CPU1]: <table width="100%" border="0"> <tr> <td><h2>Cisco CPU Utilisation Report</h2></td> </tr> <tr> <td><h3>PIX CPU</h3></td> </tr> <tr> <td><p>PIX : 10.x.x.x</p></td> </tr> </table> Target[PixConn_22]: 1.3.6.1.4.1.9.9.147.1.2.2.2.1.5.40.6&1.3.6.1.4.1.9.9.147.1.2.2.2.1.5.40.7:co [EMAIL PROTECTED]: Title[PixConn_22]: Connections Used, PIX Ylegend[PixConn_22]: Connections LegendI[PixConn_22]: Current Connections Used LegendO[PixConn_22]: Max Connections Used ShortLegend[PixConn_22]: Connections Options[PixConn_22]: absolute, gauge, growright, nopercent, integer, noinfo MaxBytes[PixConn_22]: 5000 PageTop[PixConn_22]: <H1>Connections Used, PIX</H1> Target[pix_memory22]: 1.3.6.1.4.1.9.9.48.1.1.1.5.1&1.3.6.1.4.1.9.9.48.1.1.1.6.1:[EMAIL PROTECTED] : Title[pix_memory22]: Memory Utilization Analysis for -- PIX YLegend[pix_memory22]: Memory LegendI[pix_memory22]: Memory Used LegendO[pix_memory22]: Memory Free Options[pix_memory22]: growright, gauge, integer, nopercent MaxBytes[pix_memory22]: 128000000 PageTop[pix_memory22]: <H1>Memory Utilization for -- PIX</H1> Kerry L. Werry MCSE CCNA Pivotal Corporation -----Original Message----- From: Zuber, Manfred [mailto:[EMAIL PROTECTED] Sent: February 3, 2003 8:11 AM To: [EMAIL PROTECTED] Cc: Müller, Roger Subject: [mrtg] PIX 515 MIB-Definitions Dear All Of a PIX 515 (SW Vers. 6.2) we would like to know about the following topics: - CPU consumption - Memory consumption - # of actual concurrent connections - failover information If you know, please indicate which MIBs and OIDs are good for this information and / or where to find more detailed information about this topics. Thank you very much and kind regards Manfred A. Zuber Network Engineer ______________________ SIS Systems AG Network Solutions P.O. Box CH-8022 Zurich Switzerland Phone +41-1-288-4591 Fax + 41-1-288-4800 **************************************************************************** The content of this e-mail is intended only for the confidential use of the person addressed. If you have received this message in error, please notify us immediately by electronic mail, by telephone or by fax at the above num- bers. E-mail communications are not secure and therefore we do not accept any res- ponsibility for the confidentiality or altered contents of this message. Please be aware that SIS Group and its subsidiary companies cannot accept any orders or other legally binding correspondence with a participant as part of an E-mail. The views expressed above are not necessarily those held by SIS Group and its subsidiary companies and not binding for them. ************************************************************************exfe -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
