Hi Makai
Thanks for the help I seem to be getting somewhere now.
I un-installed everything and started again and it seems to keep the index file
now.
The problem I am having now is running cfgmaker, following your advice my
command is as follows,
C:\mrtg\bin>perl cfgmaker --global "WorkDir: c:\www\mrtg" --output mrtg.cfg
1.3.6.1.2.1.25.3.3.1.2:[EMAIL PROTECTED]
The OID I got from getif being the following,
.1.3.6.1.2.1.25.3.3.1.2 -- The average, over the last minute, of the
percentage of time that this processor was not
idle.
But still I get the following error message
C:\mrtg\bin>perl cfgmaker --global "WorkDir: c:\www\mrtg" --output mrtg.cfg
1.3.6.1.2.1.25.3.3.1.2:
[EMAIL PROTECTED]
--base: Get Device Info on 1.3.6.1.2.1.25.3.3.1.2:[EMAIL PROTECTED]:
SNMP Error:
no response received
SNMPv1_Session (remote host: "host_ip" [host_ip].161)
community: "1.3.6.1.2.1.25.3.3.1.2:public"
request ID: -565799535
PDU bufsize: 8000 bytes
timeout: 2s
retries: 5
backoff: 1)
at C:/mrtg/bin\..\lib\mrtg2/SNMP_util.pm line 621
SNMPWALK Problem for 1.3.6.1.2.1.1 on 1.3.6.1.2.1.25.3.3.1.2:[EMAIL
PROTECTED]:::::v4only
at cfgmaker line 775
WARNING: Skipping 1.3.6.1.2.1.25.3.3.1.2:[EMAIL PROTECTED]: as no info could be
retreived
--base: Writing mrtg.cfg
I aslo still seem to be getting nothing from snmp2ca
Many thanks
Jaun
-----Original Message-----
From: Makai József [mailto:[EMAIL PROTECTED]
Sent: 09 December 2003 12:50
To: Jaun Keeve
Subject: RE: [mrtg] Re: [mrtg]SNMP2CA-STD/SNMP4tPC issues
Hi Jaun,
First I would use a command like
perl cfgmaker --global "WorkDir: c:\www\mrtg" --output mrtg.cfg
[EMAIL PROTECTED]
because the reference for cfgmaker say the synopsis is
cfgmaker [options] [EMAIL PROTECTED] [[options] [EMAIL PROTECTED] ...]
It is normally makes a config file for the interfaces. When you check the
config file you can see, that the OIDs are never used alone, always two of
them are used.
At the end of the OIDs you will see the instance number. Those are
important, for instance in case of the interfaces those tell you which
interface is addressed (and so with the other objects ...)
I use Getif 2.3.1, but the OIDs are never gone. Any messages in the
getif.log?
Jozsef
> -----Original Message-----
> From: Jaun Keeve [mailto:[EMAIL PROTECTED]
> Sent: Tuesday, December 09, 2003 11:06 AM
> To: [EMAIL PROTECTED]
> Subject: [mrtg] Re: [mrtg]SNMP2CA-STD/SNMP4tPC issues
>
>
> Hi
>
> I am new to this and I don't seem to be getting any of it right!!
>
> I have read the FAQ's, support pages and the history about
> the subject in this mailing list and apologies in advance if
> this annoys anyone.
>
> My first issue is this: I have installed SNMP4tPC and
> extracted the mibs. Deleted the index file and started Getif.
> This works fine, then if I close getif and open it again the
> OIDs are gone. I then have to delete the index file again as
> I did above.
>
> Secondly I install SNMP2CA-STD. This does nothing!! running
> RmSnmpExt.exe does nothing and no new OIDs can be seen.
>
> Also if I run the cfgmaker for mrtg none of the oids can be
> found, even though I can see them in Getif. I run the command
> as follows
> perl cfgmaker .1.3.6.1.2.1.1.3:[EMAIL PROTECTED] --global
> "WorkDir: c:\www\mrtg" --output mrtg.cfg
>
> I have tried excluding the first 'dot', but nothing. The
> community name is correct "[EMAIL PROTECTED]", this returns values.
>
> I know this is a mouthful, but any help would be appreciated
>
> Many thanks
>
> Jaun
>
> --
> Unsubscribe mailto:[EMAIL PROTECTED]
> Archive http://www.ee.ethz.ch/~slist/mrtg
> FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
> WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
>
--
Unsubscribe mailto:[EMAIL PROTECTED]
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
