Thanks, but before I continue with my .cfg file, I think I have to inform you that I am very new with this.. and I use MRTG only (without RRDTool), below is my .cfg file, I need your advice .. thanks a lot in advance
# Created by # /usr/bin/cfgmaker --global 'Workdir: /var/www/html/mrtg/data/proxy-ho' --global 'Workdir: /var/www/html/mrtg/data/proxy-ho' --show-op-down --output=/etc/mrtg/proxy-ho .cfg proxy-ho ### Global Config Options # for UNIX # WorkDir: /home/http/mrtg # or for NT # WorkDir: c:\mrtgdata ### Global Defaults # to get bits instead of bytes and graphs growing to the right Options[_]: growright, bits EnableIPv6: no Workdir: /var/www/html/mrtg/data/proxy-ho Icondir: /icons/ Refresh: 600 Interval: 5 RunAsDaemon: yes ###################################################################### # System: proxy-HO.lippogeneral.com # Description: Linux proxy-HO.lippogeneral.com 2.4.22-1.2115.nptl #1 Wed Oct 29 15:42:51 EST 2003 i686 # Contact: Root <[EMAIL PROTECTED]> (configure /etc/snmp/snmp.local.conf) # Location: Unknown (edit /etc/snmp/snmpd.conf) ###################################################################### ### Interface 1 >> Descr: 'lo' | Name: '' | Ip: '' | Eth: '' ### ### The following interface is commented out because: ### * it is a Software Loopback interface # # Target[proxy-ho_1]: 1:[EMAIL PROTECTED]: # SetEnv[proxy-ho_1]: MRTG_INT_IP="" MRTG_INT_DESCR="lo" # MaxBytes[proxy-ho_1]: 1250000 # Title[proxy-ho_1]: Traffic Analysis for 1 -- proxy-HO.lippogeneral.com # PageTop[proxy-ho_1]: <H1>Traffic Analysis for 1 -- proxy-HO.lippogeneral.com</H1> # <TABLE> # <TR><TD>System:</TD> <TD>proxy-HO.lippogeneral.com in Unknown (edit /etc/snmp/snmpd.conf)</TD></TR> # <TR><TD>Maintainer:</TD> <TD>Root <[EMAIL PROTECTED]> (configure /etc/snmp/snmp.local.conf)</TD></TR> # <TR><TD>Description:</TD><TD>lo </TD></TR> # <TR><TD>ifType:</TD> <TD>softwareLoopback (24)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>1250.0 kBytes/s</TD></TR> # </TABLE> ### Interface 2 >> Descr: 'eth0' | Name: '' | Ip: '' | Eth: '00-c0-9f-23-77-29' ### Target[proxy-ho_2]: 2:[EMAIL PROTECTED]: SetEnv[proxy-ho_2]: MRTG_INT_IP="" MRTG_INT_DESCR="eth0" MaxBytes[proxy-ho_2]: 12500000 Title[proxy-ho_2]: Traffic Analysis for 2 -- proxy-HO.lippogeneral.com PageTop[proxy-ho_2]: <H1>Traffic Analysis for 2 -- proxy-HO.lippogeneral.com</H1> <TABLE> <TR><TD>System:</TD> <TD>proxy-HO.lippogeneral.com in Unknown (edit /etc/snmp/snmpd.conf)</TD></TR> <TR><TD>Maintainer:</TD> <TD>Root <[EMAIL PROTECTED]> (configure /etc/snmp/snmp.local.conf)</TD></TR> <TR><TD>Description:</TD><TD>eth0 </TD></TR> <TR><TD>ifType:</TD> <TD>ethernetCsmacd (6)</TD></TR> <TR><TD>ifName:</TD> <TD></TD></TR> <TR><TD>Max Speed:</TD> <TD>12.5 MBytes/s</TD></TR> </TABLE> ----- Original Message ----- From: "Cook, Garry" <[EMAIL PROTECTED]> To: "Winanjaya" <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Sent: Tuesday, April 06, 2004 9:41 PM Subject: RE: [mrtg] 64 Kbps CIR 32 Kbps (point to point) Frame Relay WAN (Urgent) [EMAIL PROTECTED] wrote: > Dear The Expert, > We had 64 Kbps CIR 32 Kbps (point to point) Frame Relay WAN > connection to our branch, is it possible for me to use MRTG > for make me sure that our Network Provider already gave us > correct bandwidth rate? if so .. could any body please inform > me what should I do? or what should I change in my .cfg file? > I need advice .. I have stuck on this for almost 4 weeks .. > and I am getting frustated now .. > > many thanks in advance > > Regards > > Winanjaya Perhaps you could provide some more information, maybe show us your .cfg file? If you used configmaker to generate the .cfg file, it should show the correct bandwidth. You may want to set MaxBytes to 4000 (for the CIR) and AbsMax to 8000 (for the port). Other than that, I'm not sure what else you are looking for. If you still have specific questions about this, please let us know... Garry W. Cook, CCNA Network Infrastructure Manager MACTEC, Inc. - http://www.mactec.com/ 303.308.6228 (Office) - 720.220.1862 (Mobile) -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
