I want to add system and user stats together. Should I use & between the 2 OIDs like this:
1.3.6.1.4.1.42.3.13.1.0&1.3.6.1.4.1.42.3.13.3.0 Or do I need to collect them separate and use + like this: 1.3.6.1.4.1.42.3.13.1.0&1.3.6.1.4.1.42.3.13.1.0:[EMAIL PROTECTED] + 1.3.6.1.4.1.42.3.13.3.0&1.3.6.1.4.1.42.3.13.3.0:[EMAIL PROTECTED]: Brian -----Original Message----- From: PAUL WILLIAMSON [mailto:[EMAIL PROTECTED] Sent: Tuesday, January 25, 2005 10:22 AM To: [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: RE: [mrtg] Monitor Solaris CPU from MRTG You need to add a .0 to the end. I missed that you were using the walk command. If you look at the response, snmpwalk is kindly filling in the instance (.0), on to the end of your requested walk. Try to run an snmpget with the OID and the instance number appended before modifying your conf file to verify this is the problem, but I'm willing to bet that's exactly the issue. Paul >>> "Brian Steele" <[EMAIL PROTECTED]> 1/25/2005 11:17:06 AM >>> Paul, I've used the line you suggested: Target[milesv_cpu]: 1.3.6.1.4.1.42.3.13.1&1.3.6.1.4.1.42.3.13.1:[EMAIL PROTECTED] Now I get a different error: SNMPGET Problem for 1.3.6.1.4.1.42.3.13.1 1.3.6.1.4.1.42.3.13.1 on [EMAIL PROTECTED]::::::v4only at /usr/bin/mrtg line 1847 ERROR: Target[milesv_cpu][_IN_] ' $target->[8]{$mode} ' did not eval into defined data ERROR: Target[milesv_cpu][_OUT_] ' $target->[8]{$mode} ' did not eval into defined data What does v4only mean? Brian -----Original Message----- From: PAUL WILLIAMSON [mailto:[EMAIL PROTECTED] Sent: Tuesday, January 25, 2005 8:53 AM To: [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: Re: [mrtg] Monitor Solaris CPU from MRTG You must use TWO OIDs, not one, not three, but two. They must be joined in the center with an ampersand, otherwise, the magical divination shall not work. Try something like: Target[milesv_cpu]: .1.3.6.1.4.1.42.3.13.1&.1.3.6.1.4.1.42.3.13.1:[EMAIL PROTECTED]: I can't remember if you need the leading dot in each OID or not... Paul >>> "Brian Steele" <[EMAIL PROTECTED]> 1/25/2005 9:45:14 AM >>> I'm attempting to use MRTG to monitor CPU time on a Solaris 9 server. I cannot figure out how to set up the Target line. Snmpwalk works fine with the specified OID. Here is an example: >snmpwalk -v 1 -c public 192.168.150.250 .1.3.6.1.4.1.42.3.13.1 SNMPv2-SMI::enterprises.42.3.13.1.0 = Counter32: 29628917 However, when I set the target line to: Target[milesv_cpu]: .1.3.6.1.4.1.42.3.13.1:[EMAIL PROTECTED]: The result is: 0' instead of a numberpu][_IN_] '.1.3.6.1.4.1.42.3.13. $target->[8]{$mode} ' evaluated to '* 0' instead of a numberpu][_OUT_] '.1.3.6.1.4.1.42.3.13. $target->[8]{$mode} ' evaluated to '* Why does one work and the other not? Brian -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
