MRTG needs 2 OIDs in the target line. You have this Target[172.20.100.202_1]: 1:[EMAIL PROTECTED]:
You need something like this Target[172.20.100.202_1]: 1&1:[EMAIL PROTECTED]: I'm not 100% sure of the syntax since I always explicitly list whatever OIDs I am trying to get. I would do it like this: Target[172.20.100.202_1]: ifInOctets.1&ifOutOctets.1:[EMAIL PROTECTED]::::: Not sure of the mrtg shorthand. But for sure one of your issues is that you need to collect two metrics. Tanya Ruttenberg - RSIS Contractor OTSO/DNE/NMPEB [EMAIL PROTECTED] 410-965-9605 -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Aaron Clasby Sent: Wednesday, January 04, 2006 3:11 PM To: [EMAIL PROTECTED] Subject: [mrtg] mrtg frustrations I am trying to setup another Dell switch for SNMP polling. I have one switch working but am running into problems with another similar switch. I ran debug and I see it running through the config lines: --cfg: /home/mrtg/cfg/mrtg.cfg[1978]: ###################################################################### --cfg: /home/mrtg/cfg/mrtg.cfg[1979]: # System: sw3 --cfg: /home/mrtg/cfg/mrtg.cfg[1980]: # Description: Ethernet Stackable Switching System --cfg: /home/mrtg/cfg/mrtg.cfg[1981]: # Contact: Aaron Clasby --cfg: /home/mrtg/cfg/mrtg.cfg[1982]: # Location: --cfg: /home/mrtg/cfg/mrtg.cfg[1983]: ###################################################################### --cfg: /home/mrtg/cfg/mrtg.cfg[1984]: --cfg: /home/mrtg/cfg/mrtg.cfg[1985]: --cfg: /home/mrtg/cfg/mrtg.cfg[1986]: ### Interface 1 >> Descr: '' | Name: '' | Ip: '' | Eth: '' ### --cfg: /home/mrtg/cfg/mrtg.cfg[1987]: ### The following interface is commented out because: --cfg: /home/mrtg/cfg/mrtg.cfg[1988]: ### * --ifref=descr is not unique for this interface --cfg: /home/mrtg/cfg/mrtg.cfg[1989]: # --cfg: /home/mrtg/cfg/mrtg.cfg[1990]: Target[172.20.100.202_1]: 1:[EMAIL PROTECTED]: --cfg: /home/mrtg/cfg/mrtg.cfg[1991]: SetEnv[172.20.100.202_1]: MRTG_INT_IP="" MRTG_INT_DESCR="" --cfg: /home/mrtg/cfg/mrtg.cfg[1992]: MaxBytes[172.20.100.202_1]: 12500000 --cfg: /home/mrtg/cfg/mrtg.cfg[1993]: Title[172.20.100.202_1]: Traffic Analysis for 1 -- sw3 --cfg: /home/mrtg/cfg/mrtg.cfg[1994]: PageTop[172.20.100.202_1]: <H1>Traffic Analysis for 1 -- sw3</H1> --cfg: /home/mrtg/cfg/mrtg.cfg[1995]: <TABLE> --cfg: /home/mrtg/cfg/mrtg.cfg[1996]: <TR><TD>System:</TD> <TD>sw3 in </TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[1997]: <TR><TD>Maintainer:</TD> <TD>Aaron Clasby</TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[1998]: <TR><TD>Description:</TD><TD> </TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[1999]: <TR><TD>ifType:</TD> <TD>ethernetCsmacd (6)</TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[2000]: <TR><TD>ifName:</TD> <TD></TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[2001]: <TR><TD>Max Speed:</TD> <TD>100.0 Mbits/s</TD></TR> --cfg: /home/mrtg/cfg/mrtg.cfg[2002]: </TABLE> --cfg: /home/mrtg/cfg/mrtg.cfg[2003]: --cfg: /home/mrtg/cfg/mrtg.cfg[2004]: But I don't see any snpo lines, such as the ones below: --snpo: simple If: .100 --snpo: simple If: .100 --snpo: SNMPGet from [EMAIL PROTECTED]: -- ifInOctets.100,ifOutOctets.100,sysUptime,sysName --snpo: SNMPfound -- 'undef', 'undef', '32 days, 21:17:52', 'undef' I am trying to get this to work via Big Brother and I wonder if this is my overall problem. Regards, Aaron Clasby Technical Specialist Cicada Corporation 525 Central Park Dr., Suite 500 Oklahoma City, OK 73105 Desk: +1 405 609 3854 Ops: +1 405 426 7187 Fax: +1 405 524 7373 -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://lists.ee.ethz.ch/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://lists.ee.ethz.ch/lsg2.cgi -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://lists.ee.ethz.ch/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://lists.ee.ethz.ch/lsg2.cgi
