For Windows clients, they can do snmp, but also see NSCLIENT++ for more info.
Lyle Fehmi Dumani wrote: > Greetings Ashok > > There must be a way to monitor windows servers as well. Unfortunatly I > have no clue how to get information about uptime on windows machines, > I have no experience on windows machines at all, and I am new on mrtg > too, this is my second-third week of MRTG usage. > > But if you can get statistic information localy via CLI (cmd.exe) > about the windows systems I think there wont be any trouble about > getting these statistics on linux machines and create graphs. > > I will do my best to assist you on this task. > > Regards > > Fehmi. > > ------------------------------------------------------------------------ > Date: Wed, 28 Apr 2010 18:01:12 +0530 > Subject: Re: [mrtg] How to monitor non SNMP Device using MRTG > From: [email protected] > To: [email protected] > CC: [email protected] > > HiFehmi Dumani, > with your very good explanation on non snmp based mrtg monitoring I'm > able to monitor any linux system now. > But, what about windows and printers that don't have any snmp enabled > on them? > > On Mon, Apr 26, 2010 at 5:35 PM, ashok kumar <[email protected] > <mailto:[email protected]>> wrote: > > > Hi Dumani. > It's working fine now. I used scp instead of ssh-copy-id. > Thanks for your valuable time. > If I have further queries I will post in the mailing list. > Happy Posting. Take Care. Bye :) > On Mon, Apr 26, 2010 at 5:25 PM, ashok kumar > <[email protected] <mailto:[email protected]>> wrote: > > sorry Dumani, > I didn't see your line ssh-copy-id [-i [identity_file]] > [u...@]machine. > But my kernel says that *ssh-copy-id* not found. It seems I > need to install that rmp. > > On Mon, Apr 26, 2010 at 4:49 PM, Fehmi Dumani > <[email protected] <mailto:[email protected]>> wrote: > > Yes it is > > You can run commands remotly on your machines via ssh or > rsh the script is almost the same except you use command > > ssh u...@hostip uptime <------------ > instead of > uptime <------------------ > > and first you have to configure ssh and install your > public key via ssh-copy-id > > ssh-copy-id [-i [identity_file]] [u...@]machine > > and than everythink is the same. > > Regards > > > ------------------------------------------------------------------------ > Date: Mon, 26 Apr 2010 14:03:11 +0530 > > Subject: Re: [mrtg] How to monitor non SNMP Device using MRTG > From: [email protected] <mailto:[email protected]> > To: [email protected] <mailto:[email protected]> > CC: [email protected] <mailto:[email protected]> > > Hi again Dumani, > Thanks for your reply. In my previous reply I was more > concerned about the remote system monitoring rather than > my sytem. But you just mentioned about that in your last > line like "Remember you can execute commands remotely via > ssh or rsh so you can make load average graphs of other > systems as well" which means that we can have mrtg to be > running on remote machine and if you want to get that > graphs you have to use httpd service. Isn't it? > But my concern is about having all those data on my > system(server) so that I can view the graphs at anytime > and maintain log files on my system rather than running > mrtg and maintining all the data in respective systems. > Is it possible without snmp enabled on my client machines? > > On Mon, Apr 26, 2010 at 1:01 PM, Fehmi Dumani > <[email protected] <mailto:[email protected]>> wrote: > > Greetings Ashok > > On your script you are showing the VAL1 of a system > running mrtg uptime for 1 min, the second VAL2 is > showing your uptime and the and the system load > averages for the past 1, 5. Since mrtg on his own > creates a graph for periodic use in your cause every 5 > minutes you don't have to give bouth values showing > the same thing > > VAL1=`echo "$SECOND*100" | bc | cut -f1 -d"."` > > and for > > VAL2=100 > > your solid green will show the system load averages > for the past 5 minutes of the system which will be > periodically obtained. and the second line blue 100% > that might be used. > > > If I can make some modifications on your mrtg.cfg I > would make it like this: > > > EnableIPv6: no > WorkDir: /home/Ashok/mrtg2/Station21/ > Interval: 5 > Title[load_avg]: Average Load on Station21 > PageTop[load_avg]: <H1>( Average Load on Station21 ) * > 100</H1> > Options[load_avg]: nobanner,gauge,growright > > Target[load_avg]: `/home/Ashok/mrtg2/cfg/load_avg.sh` > MaxBytes[load_avg]: 100 > YLegend[load_avg]: LoadAvg * 100 > Unscaled[load_avg]: ymwd > LegendI[load_avg]: Load Average > LegendO[load_avg]: Max Load Average > > Suppress[load_avg]: y > RunAsDaemon: Yes > Refresh: 600 > > I don't use mrtg as a daemon so it is up to you if you > wana use it or do the job with crontab. All I add was > LegendI and LegendO to put Max Average and Current > show values and removed noinfo,nopercent, at options. > Remember in order to view it on your page you have to > configure httpd to set a dir > /home/Ashok/mrtg2/Station21/ to be used, also if you > have SELinux enabled you will have to run it on > permisive mode or to create your own policies, > otherwise it won't let you publish on httpd. Than all > you have to do is get the indexmaker create the > index.html and wait for some minutes to see your > graphs. (Indexmaker usage command: indexmaker > --output=/home/Ashok/mrtg2/Station21/index.html > /etc/mrtg/mrtg.cfg > > Remember you can execute commands remotely via ssh or > rsh so you can make load average graphs of other > systems as well. > > Regards > > > > ------------------------------------------------------------------------ > The New Busy think 9 to 5 is a cute idea. Combine > multiple calendars with Hotmail. Get busy. > > <http://www.windowslive.com/campaign/thenewbusy?tile=multicalendar&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_5> > > > > > -- > > Thanks > G. Ashok Kumar > Softential > > > ------------------------------------------------------------------------ > Hotmail is redefining busy with tools for the New Busy. > Get more from your inbox. See how. > > <http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_2> > > > > > -- > > Thanks > G. Ashok Kumar > Softential > > > > > -- > > Thanks > G. Ashok Kumar > Softential > > > > > Kind Regards > G. Ashok Kumar, > Softential. > > ------------------------------------------------------------------------ > Hotmail has tools for the New Busy. Search, chat and e-mail from your > inbox. Learn more. > <http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_1> > > ------------------------------------------------------------------------ > > _______________________________________________ > mrtg mailing list > [email protected] > https://lists.oetiker.ch/cgi-bin/listinfo/mrtg >
_______________________________________________ mrtg mailing list [email protected] https://lists.oetiker.ch/cgi-bin/listinfo/mrtg
