I've been testing setting the value to 0x20 (32 in decimal) which has resolved all the IPv6 problems I was experiencing.
0x20 = prefer IPv4. I am anticipating bringing online a Direct Access service someday, and I know that that won't work if IPv6 is entirely disabled. I am still testing this setting, but you might look into setting it to 0x20 rather than 0xffffffff For me, where our net switches drop all IPv6 traffic, 0x20 has been good enough. From: [email protected] [mailto:[email protected]] On Behalf Of Scott Kenyon Sent: Monday, September 23, 2013 11:52 AM To: '[email protected]' Subject: [mssms] RE: Disabling IPv6 in a Task Sequence Thanks Mark.... Scott Kenyon Sr. Computer Specialist Dean of Medicine Information Technology UW School of Medicine 850 Republican Street, Box 358047 Seattle, WA 98109 Phone: 206.685.2825 ServiceDesk: 206.221-2459 | [email protected]<mailto:[email protected]> [email protected]<mailto:[email protected]> uwmedicine.org<http://www.uwmedicine.org/> [Visit UW Medicine on.line]<http://uwmedicine.org/> The above email may contain patient identifiable or confidential information. Because email is not secure, please be aware of associated risks of email transmission. If you are communicating with a UW Medicine Provider or Researcher via email, your acceptance of the risk and agreement to the conditions for email communications is implied. (See http://www.uwmedicine.org/Global/Compliance/EmailRisk.htm.) The information is intended for the individual named above. If you are not the intended recipient, any disclosure, copying, distribution or use of the contents of this information is prohibited. Please notify the sender by reply email, and then destroy all copies of the message and any attachments. See our Notice of Privacy Practices at http://uwmedicine.washington.edu. From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of Kent, Mark Sent: Friday, September 20, 2013 12:03 PM To: [email protected]<mailto:[email protected]> Subject: [mssms] RE: Disabling IPv6 in a Task Sequence After "Setup Windows and Configmr" Mark Kent (MCP) Sr. Desktop Systems Engineer Computing & Technology Services - SUNY Buffalo State From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of Scott Kenyon Sent: Friday, September 20, 2013 2:52 PM To: '[email protected]' Subject: [mssms] RE: Disabling IPv6 in a Task Sequence I've used that command, but it had not effect. Were in the task sequence do you insert this command? I could have it in the wrong location. Thanks Scott Kenyon Sr. Computer Specialist Dean of Medicine Information Technology UW School of Medicine 850 Republican Street, Box 358047 Seattle, WA 98109 Phone: 206.685.2825 ServiceDesk: 206.221-2459 | [email protected]<mailto:[email protected]> [email protected]<mailto:[email protected]> uwmedicine.org<http://www.uwmedicine.org/> [Visit UW Medicine on.line]<http://uwmedicine.org/> The above email may contain patient identifiable or confidential information. Because email is not secure, please be aware of associated risks of email transmission. If you are communicating with a UW Medicine Provider or Researcher via email, your acceptance of the risk and agreement to the conditions for email communications is implied. (See http://www.uwmedicine.org/Global/Compliance/EmailRisk.htm.) The information is intended for the individual named above. If you are not the intended recipient, any disclosure, copying, distribution or use of the contents of this information is prohibited. Please notify the sender by reply email, and then destroy all copies of the message and any attachments. See our Notice of Privacy Practices at http://uwmedicine.washington.edu. From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of Kent, Mark Sent: Friday, September 20, 2013 11:31 AM To: [email protected]<mailto:[email protected]> Subject: [mssms] RE: Disabling IPv6 in a Task Sequence Do a Run Command Line task and use the following: REG ADD HKLM\System\CurrentControlSet\services\TCPIP6\Parameters /v DisabledComponents /t REG_DWORD /d 4294967295 Mark Kent (MCP) Sr. Desktop Systems Engineer Computing & Technology Services - SUNY Buffalo State From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of Scott Kenyon Sent: Friday, September 20, 2013 2:28 PM To: '[email protected]' Subject: [mssms] Disabling IPv6 in a Task Sequence Has anyone done this, if so could use some help on a script or something to disable IPv6 during image deployments Thanks Scott Kenyon Sr. Computer Specialist Dean of Medicine Information Technology UW School of Medicine 850 Republican Street, Box 358047 Seattle, WA 98109 Phone: 206.685.2825 ServiceDesk: 206.221-2459 | [email protected]<mailto:[email protected]> [email protected]<mailto:[email protected]> uwmedicine.org<http://www.uwmedicine.org/> [Visit UW Medicine on.line]<http://uwmedicine.org/> The above email may contain patient identifiable or confidential information. Because email is not secure, please be aware of associated risks of email transmission. If you are communicating with a UW Medicine Provider or Researcher via email, your acceptance of the risk and agreement to the conditions for email communications is implied. (See http://www.uwmedicine.org/Global/Compliance/EmailRisk.htm.) The information is intended for the individual named above. If you are not the intended recipient, any disclosure, copying, distribution or use of the contents of this information is prohibited. Please notify the sender by reply email, and then destroy all copies of the message and any attachments. See our Notice of Privacy Practices at http://uwmedicine.washington.edu. ________________________________ Notice: This UI Health Care e-mail (including attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. 2510-2521, is confidential and may be legally privileged. If you are not the intended recipient, you are hereby notified that any retention, dissemination, distribution, or copying of this communication is strictly prohibited. Please reply to the sender that you have received the message in error, then delete it. Thank you. ________________________________
<<inline: image001.gif>>
