Just like Punch and Judy said "that's the way to do it" Managed to resolve my issue, forgot to add usb hub driver, instead added 2 similar usb drivers. My colleague figured it out, suppose I spent too long on it and a fresh pair of eyes was needed.
Thanks for all suggestions. On Sunday, 12 October 2014, Chris Carbone < [email protected]> wrote: > Just thinking about it again I made a mistake, sorry. > > The date and time if wrong will bomb out (You will get a generic stop > code error and arms will be thrown in the air) after you try and run the ts > and it starts to verify everything. You are not getting this far so it's > not this but non the less, this is good to keep in the back of your mind. I > got a few more greys trying to figure this out in a critical time. > > > Sent from my mobile device. > > > -------- Original message -------- > From: Chris Carbone > Date:10/11/2014 10:56 PM (GMT-05:00) > To: [email protected] > <javascript:_e(%7B%7D,'cvml','[email protected]');> > Cc: [email protected] > <javascript:_e(%7B%7D,'cvml','[email protected]');> > Subject: RE: [mssms] Panasonic ToughPad FZ G1 OSD Nightmare. > > I've come across this a few times and it's only been two things that > have caused it. > > The date and time, at least for the surface pro's, needs to be accurate. > > The nic drivers ( its probably this one if it's getting stuck at > "preparing network connections") you might have to use older drivers and > inject them. I had to do that with the asus Eeebox that we use as dp's. > > Good luck! I hope this helps. > > > Sent from my mobile device. > > > -------- Original message -------- > From: Paul Winstanley > Date:10/10/2014 12:24 PM (GMT-05:00) > To: [email protected] > <javascript:_e(%7B%7D,'cvml','[email protected]');> > Cc: [email protected] > <javascript:_e(%7B%7D,'cvml','[email protected]');> > Subject: Re: [mssms] Panasonic ToughPad FZ G1 OSD Nightmare. > > Have you injected any storage drivers? > > > > > On 10 Oct 2014, at 16:21, Rickym61 <[email protected] > <javascript:_e(%7B%7D,'cvml','[email protected]');>> wrote: > > > > By any slim chance does anyone here image Panasonic ToughPads, mainly FZ > G1 MK1 and builds them via the docking station? (as no NIC port on the > model we have) > > > > If yes, any tricks to getting to build via SCCM, trying to get W7 x86 > image on them. > > > > We are having issues, it pxe boots, downloads the image, reboots into > WinPE, says initializing, then nothing, once it reboots into WinPE we loose > the keyboard connection, so dont even get to press F8 to check what issues > it may have. > > > > According to Panasonic I need to add 2 lots of drivers to my boot image, > > > > USB 3.0 driver & USB to LAN driver which we added both but no joy. > > > > Any takers? > > > > Thanks > > > > Ricky.. > > > > SCCM 2007 SP2 R2. > > > > > > > This electronic mail transmission may contain confidential information > intended only for the use of the individual(s) identified as addressee(s). > If you are not the intended recipient, you are hereby notified that any > disclosure, copying, distribution or the taking of any action in reliance > on the contents of this electronic mail transmission is strictly > prohibited. If you have received this transmission in error, please notify > me by telephone immediately. > > > This electronic mail transmission may contain confidential information > intended only for the use of the individual(s) identified as addressee(s). > If you are not the intended recipient, you are hereby notified that any > disclosure, copying, distribution or the taking of any action in reliance > on the contents of this electronic mail transmission is strictly > prohibited. If you have received this transmission in error, please notify > me by telephone immediately. > >
