How would I get it loaded? -r
-----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Marc Tousignant Sent: Wednesday, February 09, 2005 11:05 AM To: mythtv-users@mythtv.org Subject: [mythtv-users] RE: PVR-350 and ivtv - No sound I have put our dmesg's side by side and reorganized yours to match the same order as mine. Below I have noted what I consider major discrepancies. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.2.0 (rc3b) loading ivtv: Linux version: 2.6.9 SMP preempt PENTIUM4 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 350 card ivtv: Found an iTVC15 based chip ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 22 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x2570 vendor: 0x8086 tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] tveeprom: Hauppauge: model = 48132, rev = K168, serial# = 7336219 tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3440 (type = 11) ivtv: i2c attach [client=tveeprom[1],ok] ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model 0x00ad1598, Revision 0x00000001 ivtv: NTSC tuner detected ivtv: Radio detected saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[0],ok] saa7115: status: (1E) 0x01, (1F) 0xc0 >Mine: saa7127: video encoder driver version V 0.3 loaded saa7127: Selecting NTSC video Standard saa7127: Selecting S-Video+Composite saa7127: Turn WSS off saa7127: Widescreen Mode 4:3 Full Format saa7127: Selecting Normal Encoder Input saa7127: Enable Video Output ivtv: i2c attach [client=saa7127[0],ok] >Mine: msp34xx: ivtv version >Mine: msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) >mode, simpler (G) no-thread mode >Mine: msp34xx: $Id$ compiled on: Jan 9 2005 11:26:52 ivtv: i2c attach [client=MSP3448W-A2,ok] >Mine: ivtv: Encoder revision: 0x02040011 >Yours: ivtv: Encoder revision: 0x02040024 >Yours: ivtv: Encoder Firmware is buggy, use version 0x02040011 ivtv: Decoder revision: 0x02020023 ivtv: Configuring WinTV PVR 350 card with 9 streams ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 2 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total ivtv: Registered v4l2 device, streamtype 5 minor 16 ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total ivtv: Registered v4l2 device, streamtype 6 minor 228 ivtv: Create stream 7 ivtv: Registered v4l2 device, streamtype 7 minor 232 ivtv: Create DMA stream 8 ivtv: Registered v4l2 device, streamtype 8 minor 48 ivtv: Setting Tuner 47 tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0 ivtv: Setting audio matrix to input 3, output 1 >Yours: ivtv: i2c client addr: 0x40 not found! ivtv: Switching standard to NTSC. >Yours: ivtv: i2c client addr: 0x40 not found! ivtv: ivtv_enc_thread: pid = 5615, itv = 0xe1d63aa0 ivtv: ivtv_dec_thread: pid = 5616, itv = 0xe1d63aa0 saa7115: decoder set norm NTSC saa7115: set audio: 0x01 saa7127: Setting Encoder Video Standard saa7127: Set NTSC Video Mode saa7127: Selecting NTSC video Standard ivtv: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ==================== >Mine: saa7127: video encoder driver version V 0.3 loaded Not sure what significance this might have. >Mine: msp34xx: ivtv version >Mine: msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) >mode, simpler (G) no-thread mode >Mine: msp34xx: $Id$ compiled on: Jan 9 2005 11:26:52 Obviously, the biggest issue. You have nothing matching this in your dmesg. Since msp3400 is what causes most sound issues I believe this is where your problem is. >Mine: ivtv: Encoder revision: 0x02040011 >Yours: ivtv: Encoder revision: 0x02040024 >Yours: ivtv: Encoder Firmware is buggy, use version 0x02040011 Not sure of the impact of this. I searched out the recommended firmware because that's what it was tested with. >Yours: ivtv: i2c client addr: 0x40 not found! >Yours: ivtv: i2c client addr: 0x40 not found! Not sure of the impact of these either. This issue is relating to the IVTV driver and msp3400 you might get better support by using their mailing list as opposed to MythTV
_______________________________________________ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
