I have the same setup here, pvr250 which works, and trying to get hd3000 working. I'm very close, but i'm not sure what to do now. Using FC3 with kernel 2.6.10-1.766_FC3 and 2.0 drivers from pchdtv. Heres a snip from my modprobe.conf:
... # ivtv modules setup alias char-major-81 videodev alias char-major-81-0 ivtv #alias tveeprom tveeprom-ivtv alias msp3400 msp3400-ivtv install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c ... install cx88-atsc /sbin/modprobe cx8800;/sbin/modprobe --ignore-install cx88-atsc install cx88-dvb /sbin/modprobe cx8800;/sbin/modprobe --ignore-install cx88-dvb install btcx-risc /sbin/modprobe tuner;/sbin/modprobe --ignore-install btcx-risc Had to comment out the alias tveeprom tveeprom-ivtv or else I would get loads of unresolved symbols when modprobe cx88-atsc or cx88-dvb. I load the modules in rc.d/rc.local: ... # unload modules if they are loaded so they can be loaded # in the proper order for everything to work /sbin/rmmod lirc_i2c /sbin/rmmod lirc_dev /sbin/rmmod ivtv /sbin/rmmod saa7115 /sbin/rmmod bttv /sbin/rmmod videodev /sbin/rmmod msp3400 /sbin/rmmod tuner /sbin/rmmod i2c_algo_bit /sbin/rmmod tveeprom /sbin/rmmod i2c_core # now reload the modules, note that not all modules are reloaded # explicitly since they are automagically loaded as necessary /sbin/modprobe i2c_core /sbin/modprobe i2c_algo_bit /sbin/modprobe ivtv /sbin/modprobe lirc_i2c # next load the pchd3000 dvb module /sbin/modprobe cx88-dvb not sure if the unloading then reloading is necessary for ivtv, but i had problems with ivtv before installing hd3000. it worked for whatever reason. i'm not too sure of why/whats going on here. when the modprobe cx88-dvb goes through i see the usual messages in dmesg: ... cx88[0]/0: found at 0000:02:06.0, rev: 5, irq: 5, latency: 64, mmio: 0xfc000000 cx88[0]/0: registered device video1 [v4l2] cx88[0]/0: registered device vbi1 cx88[0]/0: registered device radio1 cx2388x dvb driver version 0.0.4 loaded cx88[0]/2: found at 0000:02:06.2, rev: 5, irq: 5, latency: 64, mmio: 0xfd000000 cx88[0]/2: cx2388x based dvb card DVB: registering new adapter (cx88[0]). DVB: registering frontend 0 (pcHDTV HD3000 HDTV)... after placing the udev 10-pchdtv.rules & .permissions in the /etc/udev/rules.d/ and permissions.d/ I modified the .permissions to change from root:users to mythtv:users in order that mythvsetup had permission to use/read/configure the dvb device. my problem now is that i can no longer change the channel in mythtv on the pvr250 card. i still haven't tried anything with the hd3000. anyone have advice on this channel changing issue? -Adam _______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
