Mine seem to be working almost right out of the box. I ran into a problem where the bttv would grab video0 before the pvr250 and scratch my head for awhile on that, but other than that it seem to be pretty painless.
Here are my suggestions, try: 1. version 0.3.5l (indicated below) 2. ATrpm kernel 2.6.10-1.770_14.rhfc3.at 3. Firmware that was shipped on the cd. 4. Removing all other capture cards. [EMAIL PROTECTED] log]# cat /etc/modprobe.conf # ivtv modules setup alias char-major-81 videodev alias char-major-81-0 ivtv alias tveeprom tveeprom-ivtv alias msp3400 msp3400-ivtv messages.1:Jun 12 00:53:59 localhost kernel: ivtv: ==================== START INIT IVTV ==================== messages.1:Jun 12 00:53:59 localhost kernel: ivtv: version 0.3.5 (l) loading messages.1:Jun 12 00:53:59 localhost kernel: ivtv: Linux version: 2.6.10-1.770_14.rhfc3.at 686 REGPARM gcc-3.4 messages.1:Jun 12 00:53:59 localhost kernel: ivtv: In case of problems please include the debug info messages.1:Jun 12 00:53:59 localhost kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when messages.1:Jun 12 00:53:59 localhost kernel: ivtv: mailing the ivtv-devel mailinglist. messages.1:Jun 12 00:53:59 localhost kernel: ivtv: Autodetected WinTV PVR 150 card messages.1:Jun 12 00:53:59 localhost kernel: ivtv: Found an iTVC16 based chip messages.1:Jun 12 00:53:59 localhost kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32) messages.1:Jun 12 00:53:59 localhost kernel: ivtv: VIA PCI device: 0x3189 vendor: 0x1106 messages.1:Jun 12 00:54:01 localhost kernel: ivtv: i2c attach [client=tveeprom[50],ok] messages.1:Jun 12 00:54:02 localhost kernel: ivtv: Tuner Type 50, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, Revision 0x00000000 messages.1:Jun 12 00:54:03 localhost kernel: ivtv: Radio detected messages.1:Jun 12 00:54:03 localhost kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 messages.1:Jun 12 00:54:04 localhost kernel: ivtv: i2c attach [client=(tuner unset),ok] messages.1:Jun 12 00:54:04 localhost kernel: ivtv: i2c attach [client=cx25840[50],ok] messages.1:Jun 12 00:54:04 localhost kernel: ivtv: i2c attach [client=wm8775[50],ok] messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Encoder revision: 0x02040024 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Configuring WinTV PVR 150 card with 5 streams messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Registered v4l2 device, streamtype 0 minor 0 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Registered v4l2 device, streamtype 1 minor 32 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Create DMA stream 1 using 97 21600 byte buffers 0 kbytes total messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Registered v4l2 device, streamtype 2 minor 224 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Create DMA stream 2 using 60 34656 byte buffers 0 kbytes total messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Registered v4l2 device, streamtype 3 minor 24 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Registered v4l2 device, streamtype 4 minor 64 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Create stream 4 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Setting Tuner 50 messages.1:Jun 12 00:54:05 localhost kernel: tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Switching standard to NTSC. messages.1:Jun 12 00:54:05 localhost kernel: ivtv: Initialized WinTV PVR 150, card #0 messages.1:Jun 12 00:54:05 localhost kernel: ivtv: ==================== END INIT IVTV ==================== On 6/14/05, Tachtevrenidis, Kosta <[EMAIL PROTECTED]> wrote: > > Dear friends, > > I am a long time Linux user but fairly new when it comes to mythtv. I > installed my PVR card (PVR-250) and I can capture TV by typing 'cat > /dev/video0 > test.mpg'. When I try Tvtime it says it can't capture from > /dev/video0 and xawtv lets me switch channels but no feed at all. As you > probably guess MythTV does not work either. Does anybody have any tips > for me? > > My specs are: > > AMD 1200Mhz 512MB RAM > Geforce MX440 64MB > PVR250 > > Here are the kernel messages( what do you guys have in your > /etc/modules.d/ivtv? ) > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.2.0 (rc3j) loading > ivtv: Linux version: 2.6.11-gentoo-r9 preempt K7 4KSTACKS gcc-3.3 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv: Autodetected WinTV PVR 250 card > ivtv: Found an iTVC16 based chip > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12 > PCI: setting IRQ 12 as level-triggered > ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 12 (level, low) -> IRQ 12 > ivtv: Unreasonably low latency timer, setting to 64 (was 32) > ivtv: XXX PCI device: 0x700e vendor: 0x1022 > tveeprom: Hauppauge: model = 32062, rev = C182, serial# = 7913366 > tveeprom: tuner = LG TAPC H791F (idx = 82, type = 39) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio_processor = MSP3445 (type = 12) > ivtv: i2c attach [client=tveeprom[0],ok] > ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model > 0x008d1612, Revision 0x00000000 > ivtv: NTSC tuner detected > ivtv: Radio detected > tuner: Ignoring new-style parameters in presence of obsolete ones > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv: i2c attach [client=(tuner unset),ok] > saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) > saa7115: detecting saa7115 client on address 0x42 > saa7115: writing init values > ivtv: i2c attach [client=saa7115[0],ok] > saa7115: status: (1E) 0x48, (1F) 0xc0 > msp34xx: ivtv version > msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode, > simpler (G) no-thread mode > msp34xx: $Id$ compiled on: Jun 13 2005 22:32:30 > ivtv: i2c attach [client=MSP3445G-B8,ok] > ivtv: Encoder revision: 0x02050032 > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > ivtv: Configuring WinTV PVR 250 card with 5 streams > ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes > total > ivtv: Registered v4l2 device, streamtype 0 minor 0 > ivtv: Create DMA stream 1 > ivtv: Registered v4l2 device, streamtype 1 minor 32 > ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total > ivtv: Registered v4l2 device, streamtype 2 minor 224 > ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes > total > ivtv: Registered v4l2 device, streamtype 3 minor 24 > ivtv: Create stream 4 > ivtv: Registered v4l2 device, streamtype 4 minor 64 > ivtv: Setting Tuner 39 > tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver > #0 > saa7115: decoder set input (4) > saa7115: now setting Composite input > ivtv: Setting audio matrix to input 3, output 1 > ivtv: Switching standard to NTSC. > ivtv: ivtv_enc_thread: pid = 4620, itv = 0xe0ac7da0 > saa7115: decoder set norm NTSC > saa7115: set audio: 0x01 > ivtv: Initialized WinTV PVR 250, card #0 > ivtv: ==================== END INIT IVTV ==================== EXT3-fs > warning: maximal mount count reached, running e2fsck is recommended > kjournald starting. Commit interval 5 seconds > EXT3 FS on hda2, internal journal > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 12 (level, low) -> IRQ 12 > smbfs: Unrecognized mount option noexec > smbfs: Unrecognized mount option noexec > saa7115: decoder set picture bright=128 contrast=63 saturation=64 hue=0 > saa7115: decoder set picture bright=128 contrast=63 saturation=63 hue=0 > saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 > saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0 > saa7115: decoder disable output > saa7115: decoder enable output > > > > > > _______________________________________________ > mythtv-users mailing list > [email protected] > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users > > > _______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
