Hi Nick,
i have listed a copy of my modprobe.conf
lias eth0 sk98lin
alias scsi_hostadapter ata_piix
alias snd-card-0 snd-intel8x0
options snd-card-0 index=0
install snd-intel8x0 /sbin/modprobe --ignore-install snd-intel8x0
&& /usr/sbin/$
remove snd-intel8x0 { /usr/sbin/alsactl store >/dev/null 2>&1
|| : ; }; /sbin/m$
alias char-major-81 bttv
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
# nvidia kernel module
alias char-major-195 nvidia-1_0-7174
alias nvidia nvidia-1_0-7174
here is the output from dmesg
Linux version 2.6.11-1.35_FC3 ([EMAIL PROTECTED]) (gcc
version 3.4.3 20050227 (Red Hat 3.4.3-22)) #1 Mon Jun 13 00:52:08 EDT
2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffb0000 (usable)
BIOS-e820: 000000001ffb0000 - 000000001ffc0000 (ACPI data)
BIOS-e820: 000000001ffc0000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 130992
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126896 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000fac50
ACPI: RSDT (v001 A M I OEMRSDT 0x02000504 MSFT 0x00000097) @
0x1ffb0000
ACPI: FADT (v002 A M I OEMFACP 0x02000504 MSFT 0x00000097) @
0x1ffb0200
ACPI: MADT (v001 A M I OEMAPIC 0x02000504 MSFT 0x00000097) @
0x1ffb0390
ACPI: OEMB (v001 A M I OEMBIOS 0x02000504 MSFT 0x00000097) @
0x1ffc0040
ACPI: DSDT (v001 A0094 A0094038 0x00000038 INTL 0x02002026) @
0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 20000000 (gap: 20000000:dfb80000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c043a000 soft=c0439000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2801.373 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513824k/523968k available (2419k kernel code, 9584k reserved,
677k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay loop... 5488.64 BogoMIPS (lpj=2744320)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080 0000441d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0820)
checking if image is initramfs... it is
Freeing initrd memory: 498k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 17 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [EMAIL PROTECTED]
** so I can fix the driver.
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1124820140.265:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8A4C334EE51D1D71
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf0000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 917504 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K PS2M ILAN PWRB
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
SCSI subsystem initialized
libata version 1.10 loaded.
ata_piix version 1.03
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xBC00 ctl 0xB882 bmdma 0xB400 irq 5
ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB482 bmdma 0xB408 irq 5
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023
88:207f
ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ata2: SATA port has no device.
scsi1 : ata_piix
Vendor: ATA Model: ST3250823AS Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 49564 usecs
intel8x0: clocking to 48000
hw_random hardware driver 1.0.0 loaded
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 5 (level, low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 5, latency: 64, mmio:
0xf8ffe000
bttv0: detected: DVICO FusionHDTV DVB-T Lite [card=128], PCI subsystem
ID is 18ac:db10
bttv0: using: DVICO FusionHDTV DVB-T Lite [card=128,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=-1
bttv0: add subdevice "dvb0"
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:02:0d.1[A] -> GSI 5 (level, low) -> IRQ 5
bt878(0): Bt878 (rev 17) at 02:0d.1, irq: 5, latency: 64, memory:
0xf8fff000
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 5, pci mem 0xf9fffc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0xc480
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0xc800
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 5, io base 0xc880
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.3: UHCI Host Controller
usb 3-2: new low speed USB device using uhci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 11, io base 0xcc00
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hiddev96: USB HID v1.10 Device [DVICO DVICO USB HID Remocon V1.00] on
usb-0000:00:1d.1-2
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03cc360(lo)
IPv6 over IPv4 tunneling driver
nvidia: no version for "struct_module" found: kernel tainted.
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar
22 06:44:39 PST 2005
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
EXT3 FS on sda3, internal journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 538168k swap on /dev/sda2. Priority:-1 extents:1
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
Trying to free free DMA3
pnp: Device 00:09 disabled.
ieee1394: Initialized config rom entry `ip1394'
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
pnp: Device 00:09 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: no IPv6 routers present
DVB: registering new adapter (bttv0).
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
TIA
Regards
Justin
> Justin,
>
> Have a look at the following resource and see if it helps at all. It
> covers most aspects of getting DVB up and running in MythTV:
>
> http://www.ethics-gradient.net/myth/mythdvb.html
>
> The process is similiar in Australia for setting up DVB, so it should
> help you along. If you want to post your /etc/modprobe.conf file and
> output of dmesg when your DVB drivers are loaded it might be useful.
>
> I would also start the frontend with verbose logging (-vv I think) to
> see if this gives any more pointers.
>
> HTH,
> Nick
> _______________________________________________
> mythtv-users mailing list
> [email protected]
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
>
>
>
_______________________________________________
mythtv-users mailing list
[email protected]
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
